background image

58

ZOLL AED 3 Administrator’s Guide

9650-000752-01 Rev. D

Entering Supervisor Configuration Mode

To enter configuration mode, follow the steps below:
1. Press and hold down the On/Off button for more than 5 seconds. Then press 

the Device Configuration icon to access the configuration window.

2. Press the Supervisor icon, and enter your six-digit passcode. You will need 

to set up the configuration settings for both the clinical archives as well as 

the device history. See the following sections for step-by-step instructions 

on both of these configuration setups.

Setting Up Clinical Archive Wi-Fi Configuration

Press the Clinical Archive Wi-Fi icon to access the Select Wi-Fi Setup Level 
window and make one of the following selections:

Quick Setup

 - for a simple configuration using the default settings (go to 

"Quick Setup for Clinical Archives" below).

IT Setup

 - for a more complex configuration using non-standard wireless 

setup settings (go to “IT Setup for Clinical Archives” on page 59).

Quick Setup for Clinical Archives

1. Press the Quick Setup button to access the Clinical Archive Quick Settings 

window and enter the applicable information in the following fields:

Network (SSID)

--Press the wireless button to the right of this field to search 

for available wireless networks. Select a network from the list and press 

OK

.

Alternately, you can use the alpha-numeric keypad to enter the SSID 
(Service Set IDentifier) name that identifies your wireless network access 
point. Press 

OK

Password (Pre-Shared Key)

 - Use the alpha-numeric keypad to enter the 

pre-shared key (password) to the wireless access point. Press 

OK

.

Server Settings

 - Press the Server Settings field to display the Server 

Settings window. Use the alpha-numeric keypad to enter the following 
server information.

Address

The default is dxsvc.zollonline.com. If you are 
using the default server, keep this entry the same. 
Otherwise, enter the URL address of the host 
server. Press 

OK

.

User ID

Use the alpha-numeric

 

keypad

 to 

enter the user-

name of the host server. Press 

OK

.

Note

: If you have set up a ZOLL Case Review 

account on zollonline.com, use the ID you specified 
for that account. 

Passcode

Use the alpha-numeric keypad to enter your pass-
word of the host server. Press 

OK

.

Note

: If you have set up a ZOLL Case Review 

account on zollonline.com, use the passcode you 
specified for that account.

Device

Configuration

icon

Supervisor
Access icon

Clinical Archive

Wi-Fi icon

Wireless

 

button

Summary of Contents for AED 3









































































Reviews: