5
Setting
Up
Your
Phone
The
nano
‐
SIM
card(s)
can
be
installed
or
removed
while
the
phone
is
turned
on.
WARNING!
To
avoid
damage
to
the
phone,
do
not
use
any
other
kind
of
SIM
cards,
or
any
non
‐
standard
nano
‐
SIM
card
cut
from
a
SIM
card.
You
can
get
a
standard
nano
‐
SIM
card
from
your
service
provider.
1.
Insert
the
tip
of
the
tray
eject
tool
into
the
hole
on
the
card
tray.
NOTE:
Please
use
the
tray
eject
tool
included
in
the
box.
Otherwise
the
card
tray
may
not
be
ejected.
CAUTION:
Never
replace
the
included
tray
eject
tool
with
sharp
objects.
Ensure
that
the
tray
eject
tool
is
perpendicular
to
the
hole.
Otherwise,
the
phone
may
be
damaged.
6
2.
Pull
out
the
card
tray.
You
can
place
a
nano
‐
SIM
card
on
the
right
card
slot,
and
place
a
nano
‐
SIM
card
or
a
microSDXC
card(optional)
on
the
left
card
slot,
as
shown.
Carefully
slide
the
tray
back
into
place.
NOTE:
The
two
card
slots
support
4G/3G/2G
networks.
Charging
the
Phone
Your
phone’s
battery
should
have
enough
power
for
the
phone
to
turn
on,
find
a
signal,
and
make
a
few
calls.
You
should
fully
charge
the
battery
as
soon
as
possible.
WARNING!
Use
only
ZTE
‐
approved
chargers
and
USB
Type
‐
C
cables.
The
use
of
unapproved
accessories
could
damage
your
phone
or
cause
the
battery
to
explode.
WARNING!
Do
not
remove
the
back
cover.
The
battery
is
not
removable.
Removal
may
cause
fire
or
explosion.
7
1.
Connect
the
adapter
to
the
charging
jack.
2.
Connect
the
charger
to
a
standard
AC
power
outlet.
3.
Disconnect
the
charger
when
the
battery
is
fully
charged.
NOTE:
If
the
battery
is
extremely
low,
you
may
be
unable
to
power
on
the
phone
even
when
it
is
being
charged.
In
this
case,
try
again
after
charging
the
phone
for
at
least
20
minutes.
Contact
the
customer
service
if
you
still
cannot
power
on
the
phone
after
prolonged
charging.
Powering
On/Off
Your
Phone
Make
sure
the
battery
is
charged
before
powering
on.
Press
and
hold
the
Power
key
to
turn
on
your
phone.
To
power
off,
press
and
hold
the
Power
key
to
open
the
options
menu,
and
touch
>
.
8
NOTE:
If
the
screen
freezes
or
takes
too
long
to
respond,
try
pressing
and
holding
the
Power
keyfor
over
10
seconds
to
restart
the
phone.
Waking
Up
Your
Phone
Your
phone
automatically
goes
into
sleep
mode
when
it
is
not
in
use
for
some
time.
The
display
is
turned
off
to
save
power
and
the
keys
are
locked
to
prevent
accidental
operations.
You
can
wake
up
your
phone
by
turning
on
the
display
and
unlocking
the
keys.
1.
Press
the
Power
keyto
turn
the
screen
on.
2.
Swipe
up
on
the
screen.
NOTE:
If
you
have
set
a
face
verification,
a
fingerprint,
an
unlock
pattern,
a
PIN
or
a
password
for
your
phone,
you’ll
need
to
use
your
face
or
fingerprint,
draw
the
pattern,
or
enter
the
PIN/password
to
unlock
your
screen.