background image

ZXHN H1600 Maintenance Management Guide

Table 7-5 Description of the Media Parameters

Parameter

Description

G722, G711U, G711A, G729,
G726, G723

Select a codec, which must be the same as that configured in the
SoftSwitch system.

VAD

Select a codec, which must be the same as that configured in the
SoftSwitch system.

Codec Priority

You can modify priority through this parameter. A lower number
indicates a higher priority.

3. Click 

Apply

 button to apply the changes.

7.6 Configure the Fax

The ZXHN H1600 supports the T30 and T38-based fax feature. By default, the T38 pro-
tocol is used.

Steps

1. On the main page of the ZXHN H1600 device, select 

VoIP > Fax

. The 

Fax

 page is

displayed, see 

Figure 7-7

.

Figure 7-7 Fax Page

2. Set the parameters. For a description of the parameters, refer to 

Table 7-6

.

Table 7-6 Parameter Descriptions for the Fax

Parameter

Description

Enable T38 Protocol

Whether to enable the T38 protocol.
If the 

Off

 button is selected, the T30 protocol is used.

3. Click 

Apply

 button to apply the changes

7-6

SJ-20200218145027-006 | 2021-03-04(R1.0)

Summary of Contents for ZXHN H1600














































































































Reviews: