Adjustment Instructions
All crimp tools wear, which increases
the crimp diameter after many crimps.
When the crimps start to approach the
maximum ring diameter, then adjust
the back pin (see figure on right). To
adjust for a tighter crimp, remove the
E-clip (for example, pop it off with a
screwdriver), slide the back pin head
out about 1/4 inch, rotate the back pin
until the line on the hex head points to
the next highest number on the tool
body, push the pin back in, and
refit the E-clip. Five adjustments
are available.
Maintenance
For easier, better crimps and longer
tool life, keep tool clean and rust-free
inside and out. Lubricate all moving
parts frequently with light oil.
For a tighter crimp, turn mark on pin to
the next number:
OPERATING INSTRUCTIONS
Zurn PEX Crimp Tools
- QCRT2CM, QCRT3CM, QCRTJCM, QCRT4CM
Form No. ZMKTG370-93, Rev. 04/16
ZURN PEX
®
,
INC.
116 Maple Street, Commerce, TX 75428 Phone: 855-ONE-ZURN (855-663-9876) • 1-800-209-2148
Note: For troubleshooting and repair
assistance, do not return tool directly to
wholesaler. Call Zurn Customer Care for
assistance at 1-855-ONE-ZURN.
See www.zurn.com for warranty information.
Zurn PEX Crimp Tools – QCRT2CM, QCRT3CM, QCRTJCM, QCRT4CM
Adjustment Instructions
ZURN PEX PLUMBING AND RADIANT HEATING SYSTEMS
1801 PITTSBURGH AVENUE, ERIE, PA, U.S.A. 16502 PHONE: 800/872-7277 FAX: 800/209-2148 www.zurn.com
IN CANADA:
ZURN INDUSTRIES LIMITED
3544 NASHUA DRIVE, MISSISSAUGA, ONTARIO L4V 1L2 PHONE: 905/405-8272 FAX: 905/405-1292
Form No. ZPM04140, Rev. 6/07
Adjustment Instructions
All crimp tools wear, which increases the crimp diameter after many
crimps. When the crimps start to approach the maximum ring
diameter, then adjust the back pin (see the table, below right and
the figure below). To adjust for a tighter crimp, remove the E-clip
(for example, pop it off with a screwdriver), slide the back pin head
out about 1/4 inch, rotate the back pin until the line on the hex
head points to the next highest number on the tool body, push the
pin back in, and refit the E-clip. Five adjustments are available.
0
5
3
1
4
2
Back
Pin
Pop-off
E-clip
Maintenance
For easier, better crimps and longer tool life, keep tool clean and
rust-free inside and out. Lubricate all moving parts frequently with
light oil.
For a tighter crimp, turn mark on pin to the next number:
0
1
2
3
4
5
Zurn PEX Crimp Tools – QCRT2CM, QCRT3CM, QCRTJCM, QCRT4CM
Adjustment Instructions
ZURN PEX PLUMBING AND RADIANT HEATING SYSTEMS
1801 PITTSBURGH AVENUE, ERIE, PA, U.S.A. 16502 PHONE: 800/872-7277 FAX: 800/209-2148 www.zurn.com
IN CANADA:
ZURN INDUSTRIES LIMITED
3544 NASHUA DRIVE, MISSISSAUGA, ONTARIO L4V 1L2 PHONE: 905/405-8272 FAX: 905/405-1292
Form No. ZPM04140, Rev. 6/07
Adjustment Instructions
All crimp tools wear, which increases the crimp diameter after many
crimps. When the crimps start to approach the maximum ring
diameter, then adjust the back pin (see the table, below right and
the figure below). To adjust for a tighter crimp, remove the E-clip
(for example, pop it off with a screwdriver), slide the back pin head
out about 1/4 inch, rotate the back pin until the line on the hex
head points to the next highest number on the tool body, push the
pin back in, and refit the E-clip. Five adjustments are available.
0
5
3
1
4
2
Back
Pin
Pop-off
E-clip
Maintenance
For easier, better crimps and longer tool life, keep tool clean and
rust-free inside and out. Lubricate all moving parts frequently with
light oil.
For a tighter crimp, turn mark on pin to the next number:
0
1
2
3
4
5
Zurn PEX Crimp Tools – QCRT2CM, QCRT3CM, QCRTJCM, QCRT4CM
Adjustment Instructions
ZURN PEX PLUMBING AND RADIANT HEATING SYSTEMS
1801 PITTSBURGH AVENUE, ERIE, PA, U.S.A. 16502 PHONE: 800/872-7277 FAX: 800/209-2148 www.zurn.com
IN CANADA:
ZURN INDUSTRIES LIMITED
3544 NASHUA DRIVE, MISSISSAUGA, ONTARIO L4V 1L2 PHONE: 905/405-8272 FAX: 905/405-1292
Form No. ZPM04140, Rev. 6/07
Adjustment Instructions
All crimp tools wear, which increases the crimp diameter after many
crimps. When the crimps start to approach the maximum ring
diameter, then adjust the back pin (see the table, below right and
the figure below). To adjust for a tighter crimp, remove the E-clip
(for example, pop it off with a screwdriver), slide the back pin head
out about 1/4 inch, rotate the back pin until the line on the hex
head points to the next highest number on the tool body, push the
pin back in, and refit the E-clip. Five adjustments are available.
0
5
3
1
4
2
Back
Pin
Pop-off
E-clip
Maintenance
For easier, better crimps and longer tool life, keep tool clean and
rust-free inside and out. Lubricate all moving parts frequently with
light oil.
For a tighter crimp, turn mark on pin to the next number:
0
1
2
3
4
5
