Chapter 23 WAN Setup
P-793H User’s Guide
253
The following table describes the fields in this menu.
23.3 Dial Backup Interface
In the SMT, to set up the auxiliary port for use, first make sure you have set up the switch and
port connection. Then, use the following menus.
1
Menu 2 - WAN Setup
2
Menu 2.2 - Dial Backup Setup
3
Menu 2.2.1 - Advanced Dial Backup Setup and
4
Menu 11.1 - Remote Node Profile (node 8, Backup ISP)
23.4 Configuring Dial Backup in Menu 2
From the main menu, enter 2 to open menu 2.
Figure 145
Menu 2.2: Dial Backup Setup
Table 96
Menu 2.1: Traffic Redirect Setup
FIELD
DESCRIPTION
Active
Use this field to turn the traffic redirect feature on (
Yes
) or off (
No
).
Configuration
Backup
Gateway IP
Address
Type the IP address of your backup gateway in dotted decimal notation. The ZyXEL
Device automatically forwards traffic to this IP address if the ZyXEL Device's Internet
connection terminates.
Metric
This field sets this route's priority among the routes the ZyXEL Device uses.
The metric represents the "cost of transmission". A router determines the best route
for transmission by choosing a path with the lowest "cost". RIP routing uses hop
count as the measurement of cost, with a minimum of "1" for directly connected
networks. The number must be between "1" and "15"; a number greater than "15"
means the link is down. The smaller the number, the lower the "cost".
When you have completed this menu, press [ENTER] at the prompt “Press ENTER to Confirm…” to
save your configuration, or press [ESC] at any time to cancel.
Menu 2.2 - Dial Backup Setup
Dial-Backup:
Active= No
Port Speed= 115200
AT Command String:
Init= at&fs0=0
Edit Advanced Setup= No
Summary of Contents for G.SHDSL.bis 4-port Security Gateway P-793H
