ZyXEL Communications USG110 User Manual Download | Manualshive

Page: 417 / 1090

background image

Chapter 11 Routing

ZyWALL USG Series User’s Guide

417

11.4 Policy Routing Technical Reference

Here is more detailed information about some of the features you can configure in policy routing.

NAT and SNAT

NAT (Network Address Translation - NAT, RFC 1631) is the translation of the IP address in a packet in one
network to a different IP address in another network. Use SNAT (Source NAT) to change the source IP
address in one network to a different IP address in another network.

Assured Forwarding (AF) PHB for DiffServ

Assured Forwarding (AF) behavior is defined in RFC 2597. The AF behavior group defines four AF classes.
Inside each class, packets are given a high, medium or low drop precedence. The drop precedence
determines the probability that routers in the network will drop packets when congestion occurs. If
congestion occurs between classes, the traffic in the higher class (smaller numbered class) is generally
given priority. Combining the classes and drop precedence produces the following twelve DSCP
encodings from AF11 through AF43. The decimal equivalent is listed in brackets.

Maximize Bandwidth Usage

The maximize bandwidth usage option allows the Zyxel Device to divide up any available bandwidth on
the interface (including unallocated bandwidth and any allocated bandwidth that a policy route is not
using) among the policy routes that require more bandwidth.

When you enable maximize bandwidth usage, the Zyxel Device first makes sure that each policy route
gets up to its bandwidth allotment. Next, the Zyxel Device divides up an interface’s available bandwidth
(bandwidth that is unbudgeted or unused by the policy routes) depending on how many policy routes
require more bandwidth and on their priority levels. When only one policy route requires more
bandwidth, the Zyxel Device gives the extra bandwidth to that policy route.

When multiple policy routes require more bandwidth, the Zyxel Device gives the highest priority policy
routes the available bandwidth first (as much as they require, if there is enough available bandwidth),
and then to lower priority policy routes if there is still bandwidth available. The Zyxel Device distributes
the available bandwidth equally among policy routes with the same priority level.

11.5 Routing Protocols Overview

Routing protocols give the Zyxel Device routing information about the network from other routers. The
Zyxel Device stores this routing information in the routing table it uses to make routing decisions. In turn,
the Zyxel Device can also use routing protocols to propagate routing information to other routers.

Table 141 Assured Forwarding (AF) Behavior Group

CLASS 1

CLASS 2

CLASS 3

CLASS 4

Low Drop Precedence

AF11 (10)

AF21 (18)

AF31 (26)

AF41 (34)

Medium Drop Precedence

AF12 (12)

AF22 (20)

AF32 (28)

AF42 (36)

High Drop Precedence

AF13 (14)

AF23 (22)

AF33 (30)

AF43 (38)

«
...
415
416
417
418
419
...
»

Summary of Contents for USG110



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for USG110

Brand: PaloAlto Networks Pages: 2

ZyXEL ZyWALL 35

Brand: ZyXEL Communications Pages: 704

Brand: Watchguard Pages: 8

Brand: Cisco Pages: 1354

Brand: Cisco Pages: 1224

Brand: Cisco Pages: 6

Brand: Cisco Pages: 2

Brand: IBASE Technology Pages: 69

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands