background image

Chapter 6 Wireless LAN

WRE2206 User’s Guide

40

Many types of encryption use a key to protect the information in the wireless network. The longer 
the key, the stronger the encryption. Every wireless client in the wireless network must have the 
same key.

6.3.1.3  WPS

WiFi Protected Setup (WPS) is an industry standard specification, defined by the WiFi Alliance. WPS 
allows you to quickly set up a wireless network with strong security, without having to configure 
security settings manually. Depending on the devices in your network, you can either press a 
button (on the device itself, or in its configuration utility) or enter a PIN (Personal Identification 
Number) in the devices. Then, they connect and set up a secure network by themselves. See how 
to set up a secure wireless network using WPS in the 

Section 5.2 on page 26

6.4  General Wireless LAN Screen 

Use this screen to enable the Wireless LAN, enter the SSID and select the wireless security mode.

Note: If you are configuring the WRE2206 from a computer connected to the wireless 

LAN and you change the WRE2206’s SSID, channel or security settings, you will 

lose your wireless connection when you press 

Apply

 to confirm. You must then 

change the wireless settings of your computer to match the WRE2206’s new 

settings.

Click 

Network

 > 

Wireless LAN 

to open the 

General 

screen.

Figure 28   

Network > Wireless LAN > General 

The following table describes the general wireless LAN labels in this screen.

Table 12   

Network > Wireless LAN > General

LABEL

DESCRIPTION

WLAN STA 
Information

This shows the wireless and security settings of the selected AP wireless network.

SSID

This displays the Service Set IDentity of the wireless device to which you are connecting.

WLAN AP 
Information / 
Wireless Setup

Use this section to configure the wireless settings between the WRE2206 and its wireless 
clients.

Name(SSID)

(Service Set IDentity) The SSID identifies the Service Set with which a wireless station is 
associated. Wireless stations associating to the access point (AP) must have the same SSID. 
Enter a descriptive name (up to 32 printable 7-bit ASCII characters) for the wireless LAN. 

Summary of Contents for WRE2206







































































Reviews: