3 Day Blinds VINYL BLINDS Getting Started Download

Page: 1 / 10

| Vinyl Blinds

GETTING STARTED

Steel Tape Measure

Power Drill and

Drill Bits

Awl (or tool for starting

a screw hole)

Level

Pencil

Flathead & Phillips

Screwdriver

Included in your order is all the hardware necessary for a

normal installation. Depending on the mounting surface,

fasteners other than the screws provided may be required.

Wall board and plaster require the use of anchors such as

expansion or toggle bolts. Bricks, tile and stone need special

plugs and drill bits. Wood should always be pre-drilled to

avoid splitting.
Professional installation is also available in most areas,

call 800-800-3329.

A few simple tools are required:

VINYL BLINDS

STANDARD HARDWARE

End Brackets

(Open Position LH & RH)

Screws

Center Support

Bracket(s)

Regular Valance Clips

Button Valance Clips

Outside Mount

Slat Valance

Inside Mount

Slat Valance

Summary of Contents for VINYL BLINDS











Search results

Summary of Contents for VINYL BLINDS

Reviews:

Related manuals for VINYL BLINDS

Brands by name

Popular brands

3 Day Blinds VINYL BLINDS, Getting Started

Search results

Summary of Contents for VINYL BLINDS

Reviews:

Related manuals for VINYL BLINDS

Brands by name

Popular brands