3M RANDOM ORBITAL SANDERS Service Instructions Download

Page: 1 / 5

34-8700-5191-8

Revision 10/03/07

3M™ Overhaul Service Kit

The part number 20347,

3M™ Overhaul Service Kit, contains all the replacement parts that naturally

wear over time and a straightforward manual to make servicing a 3M™ sander simple. Overhauling the

Random Orbital Sander can be made even easier with the use of the above Service Tools. The Service

Tools also reduce the chance of improper assembly.

SERVICE INSTRUCTIONS FOR

3M™ 12,000 RPM 5 in. (127 mm)

and 6 in. (150 mm)

RANDOM ORBITAL SANDERS

Part Number

Description

Qty

3MA0040

EXTERNAL RETAINING RING

3MA0021

BEARING - 2 SHIELDS

3MB0005

ROTOR

3MA0010

VANE

3MA0041

WOODRUFF KEY

3MA0042

O-RING

3MA0019

BEARING - 2 SHIELDS

3MA0938

DOUBLE ROW ANGULAR CONTACT BEARING - 1 SEAL

3MA0039

INTERNAL RETAINING RING

3MA0062

INTERNAL MUFFLER

3MA0068

MUFFLER INSERT

3MA0007

VALVE

3MA0009

VALVE SEAT

3MA0014

VALVE SPRING

3MA0043

O-RING

3MA0008

VALVE STEM ASSEMBLY

3MA0166

MUFFLER HOUSING

3MA0016

SPACER

3MA1417

INSTRUCTIONS FOR 5 in. AND 6 in. ROS OVERHAUL SERVICE KIT

Summary of Contents for RANDOM ORBITAL SANDERS






Search results

Summary of Contents for RANDOM ORBITAL SANDERS

Reviews:

Related manuals for RANDOM ORBITAL SANDERS

Brands by name

Popular brands

3M RANDOM ORBITAL SANDERS, Service Instructions

Search results

Summary of Contents for RANDOM ORBITAL SANDERS

Reviews:

Related manuals for RANDOM ORBITAL SANDERS

Brands by name

Popular brands