background image

GAS FIRED COMMERCIAL COPPER BOILERS

User's Manual

PRINTED IN THE U.S.A. 0212 

321082-000

Thank  you  for  buying  this  energy  efficient  boiler. 

 

We appreciate your confidence in our products.

MODELS: HW  

300, 399, 420, 520, 670

FOR HYDRONIC HEATING AND  

HOT WATER SUPPLY

UP - FLOW MODELS

OPERATION - MAINTENANCE -  

LIMITED WARRANTY

25589, Highway 1

McBee, SC 29101

WARNING:  If   the information   in   these

instructions is not followed exactly, a fire

or explosion may result causing property

damage, personal injury or death.

Do  not store  or  use  gasoline  or other

flammable   vapors  and  liquids   in  the

vicinity of this or any other appliance.

WHAT TO DO IF YOU SMELL GAS:

Do not try to light any appliance.
Do not  touch any electrical switch;  do

not use any phone in your building.
Immediately   call   your   gas   supplier

from a  neighbor’s  phone.   Follow the

gas supplier’s instructions.
If you cannot  reach your  gas supplier,

call the fire department.

Installation     and    service    must    be

performed   by   a    qualified    installer,

service agency or the gas supplier.


H

Summary of Contents for Burkay HW-300





























Reviews: