AB Marine Gori Installation Instructions Manual Download

Page: 1 / 8

[Gori 2-Blade Saildrive Propeller Installation and Maintenance Instructions, 6/21/2022]

Distributed By

AB Marine, Inc ▪ 747 Aquidneck Ave ▪ Middletown ▪ RI 02842

Tel: 401-847-

7960 ▪ Fax: 401

-849-0631

Email:

Sales@AB-Marine.com

▪ Website: www.AB

-Marine.com

Gori 2-Blade Saildrive Installation Instructions

Table of Contents

Gori 2-Blade Saildrive Installation Instructions ................................................................................... 1

Parts List .................................................................................................................................... 1

Schematic Drawings .................................................................................................................... 2

Saildrive Nut Socket Sizes ............................................................................................................ 2

Torque Settings ........................................................................................................................... 2

Installing the Propeller ................................................................................................................. 3

Removing the Propeller ................................................................................................................ 5

Replacing the Collar Zinc .............................................................................................................. 5

Removing the blades from the Blade Housing .................................................................................... 6

Operating Instructions .................................................................................................................... 7

Ahead ........................................................................................................................................ 7

Astern ........................................................................................................................................ 7

Sailing ....................................................................................................................................... 7

Cleaning and Maintenance ............................................................................................................... 8

Annual Maintenance ..................................................................................................................... 8

Underwater Installation ................................................................................................................ 8

Parts List

Hub

1 x each

Blades

2 x each

Pins

2 x each

Washer

1 x each

Shaft nut

1 x each

Split pin

1 x each not used on all installations

Allen screws

2 x each

Allen screws

2 x each

Locking bolt

1 x each

10 Collar zinc

1 x each … 2 x halves

11 Zinc screws

4 x each

12 Loctite 243

1 x bottle

13 Allen key

4mm

14 Allen key

5mm

Summary of Contents for Gori









Search results

Summary of Contents for Gori

Reviews:

Related manuals for Gori

Brands by name

Popular brands

AB Marine Gori, Installation Instructions Manual

Search results

Summary of Contents for Gori

Reviews:

Related manuals for Gori

Brands by name

Popular brands