ISSUED 03-28-19
6600EO-1-03.DWG
COVER
LOCKING THUMB TURN (If used)
#8 x 1/2" FHSMS
TRIM PLATE
MORTISE LOCK
8-32 x 1/4" FHMS
12-24 x 3/4" FH COMBO
10-32 x 1-3/4" FHMS
8-32 x 3/8" FHMS
10-32 x 1/4" PAN HD. M.S.
PUSH OR PULL HANDLE ASSY
EXIT ONLY PLATE
ADAPTER PLATE
8
1
4
12
13
11
10
5
14
15
2
1
6
14
15
13
12
11
2
2
1
10
9
4
1
2
2
2
5
6
7
1
3
4
4
1
ITEM
1
QTY
1
PART DESCRIPTION
INSTALLATION INSTRUCTIONS:
1. Install mortise lock (item 10) using (2) 12-24 screws (item 12). Then mount the trim plate (item 11) using (2) 8-32 screws (item 13).
2. Before mounting adapter plate (item 6) & exit only plate (item 8), determine which side of the door will receive the push or pull handle
assembly (item 4) and the direction the handle will mount. Handle can be mounted up, down or horizontally.
3. Mount adapter plate (item 6) & exit only plate (item 8) to door with (2) 10-32 screws (item 5) thru door and mortise lock to (2) 10-32 sex
bolts (item 7). tighten securely.
4. Before mounting handle assembly (item 4), cam pin must be rotated towards the correct side of the handle (see detail A).
5. Mount handle assembly (item 4) to adapter plate (item 6) with (4) 10-32 screws (item 3) with (4) star washers (item 9).
6. Test lock for proper operation. If latch bolt does not extend or retract freely because of any type of binding, loosen mounting screws to
adjust alignment of trim handle assembly (item 4) and re-tighten screws one at a time while checking latch bolt movement.
7. Place cover (item 1) over handle assembly (item 4) and secure with (2) 8-32 screws (item 2) on each side.
8. If provided, install locking thumb turn (item 14) using (2) #8 screws (item 15).
PATENT No. 6,196,599 & 5,730,478
2
3
1
9
#10 STAR WASHER
6600EO
PAGE 1 OF 3
NOTES
1. TRIM CAN BE MOUNTED UP, DOWN, HORIZONTALLY OR VERTICALLY.
2. VISION LITE MUST BE AT LEAST 6" FROM CENTERLINE OF TRIM.
3. USES 6600EO SERIES MORTISE LOCK DOOR PREP.
4. 6600EO MORTISE LOCK CYLINDER & LOCK CAM NOT PROVIDED.
**
SQUARE
-OR-
ROUND
COVER
NOTE:
BEFORE MOUNTING BASE ASSEMBLIES
CAM PIN MUST BE ROTATED TOWARDS
SIDE INDICATED BY ARROW STAMPED
ON THE BASE.
HINGE SIDE)
HANDLE
HORIZONTAL
(MUST POINT
DOWN
HANDLE
UP
HANDLE
*
*
EDGE GUARD NOTE:
WHEN PREPPING THE DOOR,
DETERMINE IF THE DOOR WILL
RECEIVE AN EDGE GUARD, IF SO,
THE EDGE GUARD SHOULD BE
INSTALLED FIRST AND THEN THE
PREP FOR THE MORTISE LOCK
SHOULD BE MEASURED FROM THE
OUTSIDE EDGE OF THE EDGE
GUARD.
DETAIL "A"
CAM SHAFT
6600EO SERIES EXIT ONLY PUSH/PULL
HANDLE INSTALLATION FOR MORTISE LOCK
PUSH SIDE
OR
PULL SIDE
8
7
12-24 x 1/2" SEX BOLT
2
PUSH SIDE
SHOWN
FOR
EXAMPLE
U
LISTED
L
C
R
US
c
