background image

 

 

 

 

This manual contains important safety instructions. Please follow all instructions carefully during 

installation. Read this manual thoroughly before attempting to unpack, install or operate. 

CAUTION 

˙

    To prevent the risk of fire or electric shock, install in a temperature and humidity controlled 

indoor area, free of conductive contaminants. 

˙

    Risk of electric shock, do not remove the cover. No user serviceable parts. Refer servicing to 

qualified service personnel. 

˙

    Risk of electric shock, hazardous live parts inside this UPS can be energized from the battery 

supply even when the input AC power is disconnected. 

˙

    Risk of electric shock, Battery Circuit is not isolated from AC input, hazardous voltage may 

exist between battery terminals and ground. Test before touching. 

 

NOTE

  The UPS is designed to be used with computer loads only. 

 

SETUP

 

Step 1

Inspection 

Inspect the UPS upon receipt. Notify the carrier and dealer if 

there is damage. The package is recyclable; save it for reuse or 

dispose off properly. 

Step 2

Placement 

……………………………………………………………………………………………….. 

Step 3

Check the Site Wiring Fault Indicator (115V only) 

Caution

If the site wiring fault indicator lights, get a qualified 

         electrician to correct the building wiring.

   

…………………………………………………………

 

Step 4

Connect the loads 

First, connect the UPS with the AC Mains, then plug the loads 

into the output connectors on the rear of the UPS. To use the   

UPS as a master “On/Off” switch, make sure that all of the   

loads are switch “On”. 

 

Caution

Do not connect a laser printer   

to the outlets. These UPS outlets provide   

battery power and surge protection to the   

equipment when utility voltage is outside   

acceptable limits.

 

Ablerex 

625L/1000L/1500L 

625VA 

1000VA / 

1500VA 

1000VA/ 1500VA 

625VA 

Step 5

Connect telephone / Network Surge protection 

Connect a single line telephone or a 10 base-T / 100 base-T   

network cable into the RJ-45 / RJ-11 telephone / network surge 

protection “IN” jack on the back of the UPS. Connect from the   

“OUT” jack with telephone cable or network cabling to a fax 

modem or network port. 

……………………………………………………………………………..…………………………

 

Step 6

Connect Computer Interface Port (Optional) 

Connect the optional interface cable to the USB interface port   

on the back of the UPS. Connect to the computer.   

See software document for installation instruction.   

……………………………………………………………

 

Step 7

Operation Test (for Ablerex 625L) 

a. Connect the UPS to the wall receptacle. 

b. Push on the Main Switch to check the Green Line (

) LED is on. 

c. Connect your computer equipment with sockets of the UPS and pull off the input power cable of the 

UPS from the wall receptacle to check if the Line (

) LED is flashing every 3 seconds. 

Meanwhile, please check if alarm buzzer is beeping. 

d. Try the field working condition by running some application programs on your computer and 

repeating step. 

e. Check if the UPS is initiated properly to support continuous operation. 

……………………………………………………………………………..…………………………

 

Step 8

Operation Test (for Ablerex 1000L/1500L) 

a. Connect the UPS to the wall receptacle. 

b. Push on the Main Switch to check the Green Line (

) LED is on. 

c. Connect your computer equipment with sockets of the UPS and pull off the input power cable of the 

UPS from the wall receptacle to check if the Line (

) and Inverter (

) LED are flashing every 2 

seconds. Meanwhile, please check if alarm buzzer is beeping. 

d. Try the field working condition by running some application programs on your computer and 

repeating step. 

e. Check if the UPS is initiated properly to support continuous operation. 

IMPORTANT NOT

E:Plug the UPS into the wall outlet to charge the UPS for over 8 hours before using.

 

FRONT  PANEL  EXPLANATION

 

ABLEREX 625L 

1.

 

Line LE

D

 (

)

: 

˙

  Green LED remains standstill when Utility is normal. 

˙

  Green LED flashes every 3 seconds and simultaneously buzzer alarms 

  continuously when Utility failure. 

˙

  Green LED flashes every 3 seconds when the UPS is in Battery charging   

Mode. 

˙

  Green LED remains standstill and simultaneously buzzer alarms continuously when the UPS is in 

overload condition. 

1

3

2

Reviews: