background image

Dispensing water:

Press a container or a glass against the lever until the
desired level of water is completed.
The container to collect water retains any
drops that may fall while you are dispensing water.
Use a dry cloth to clean or dry the container to collect water.

Cleaning the tank: 

Clean the tank frequently. For cleaning, never use the
dishwasher. Remove the water tank by turning it and
withdrawing it in the direction indicated in the 

fi

 gure.

Support the tank and remove the lid. 
Disengage the tip of the valve by turning it to the
left until you feel that the piece is loose.
Remove it and clean it carefully.
Use sponge or soft cloth moistened with
detergent or neutral soap. Rinse well
and dry with a clean dry cloth. 

Important:

Do not remove the body of the
valve, indicated in the 

fi

 gure.

 

Re

fi

 lling the tank:

Fit and lock the valve again, as shown in the 

fi

 gure.

Important:

Before replacing the tank, verify that the
valve is correctly installed. 

Install the tank on the side hooks
and in the hole in the door. 

Verify that the tank is 

fi

 rmly installed.

Note the absence of spaces between the support

and the door. 

Your refrigerator has a system that allows you to dispense cold water without 

opening the door, thus avoiding excessive door openings, consequently, 

reducing energy consumption.

Filling tank:

To 

fi

 ll up water in the tank, turn the lid on and

fi

 ll it with a jug. After 

fi

 lling, close the funnel

cover, turning it to the initial (closed) position.

Important:

Exclusive use for water.

Any other liquid may cause malfunction of the product.
Only use potable water to 

fi

 ll the tank.

The manufacturer is not responsible for damage caused to the system if the 
tank is supplied with any other type of liquid other than water.

Adjust the refrigerator’s racks according to the way the refrigerator is used. 

To remove the shelves: 

1. Remove all items from the shelves. 
2. Lift the top. 
3. Slide the grill out. 

To replace the shelves: 

1. Ensure that the molding tab is positioned up,

  according to the image. 
2. Place the back of the shelf

  on the rails located on the side walls. 
3. Guide the front of the grill onto the rails. 
4. Slide it in until it stops.

Procedure for cleaning doors and cabinets with signi

fi

 cant rust stains:

Keep the refrigerator in a dry environment. As moisture builds up, the metal 

rusts and rust will keep developing.

Manual cleaning method

 

Remove the shelf

Care of your refrigerator

To defrost, follow these instructions:

1. Press the button on the temperature control.

  Defrost starts automatically.
2. Once the defrosting is complete, remove the meat tray and / or
  defrost, empty the water and insert the tray again.
3. Thoroughly dry the freezer and the entire interior of the refrigerator with 

a soft cloth.

4. The refrigerator, once the defrosting is 

fi

 nished, will automatically work 

again without having to re-select the temperature.

NOTE:

 Do not use sharp or pointy objects to

 

remove frost from the freezer.

 

This will damage the evaporator.

1. Moisten a 

sponge in 

water with 

detergent. 

2. Use the soft 

surface of the 

sponge to rub 

over the rust 

stain. The 

rubbing should 

be in the 

same sense of 

polishing. 

3. Use the hard 

surface to rub 

over the rust 

stain.

 The 

rubbing 

should be in the 

same direction 

of the grain.

4. Rinse the 

sponge with 

tap water until 

the detergent is 

removed.

5. Moisten the 

fi

 ber 

in water.

6. Dry the 

surface of the 

unit well with 

the sponge.

7. Use a piece of 

dry cloth and 

rub on the wet 

surface. It is 

recommended 

to use a 

stainless steel 

cleaner for a 

shiny 

fi

 nish.

A

- Hard surface

B

- Smooth 

surface

Tools needed:

•  Piece of dry cloth
•  Soft / hard surface sponge

Water dispenser (some models)

Tank

Turn the funnel lid outwards to 

fi

 ll the tank

Recipient to 

collect water

Lever

VERY IMPORTANT

IT IS THE RESPONSIBILITY OF THE USER TO VERIFY THE FOLLOWING 

INFORMATION BEFORE CALLING THE TECHNICIAN: 
If you followed the instructions in the installation, use and care manual 

correctly, and have questions about the operation of the refrigerator, this guide 

offers solutions to problems you can detect and correct in your home.

IF THE REFRIGERATOR DOES NOT WORK

• Connect the plug directly, DO NOT USE CORD EXTENSIONS. 
• Check the ELECTRICAL CONTACT, IT COULD BE DAMAGED, connect 

another device and test if it works. 

• Avoid starting several devices at the same time; THE ELECTRICAL 

INSTALLATION MAY OVERLOAD. 

• Verify that the TEMPERATURE CONTROL IS IN THE ON-OFF POSITION. 
• Make sure the refrigerator is NOT NEXT TO A HEAT SOURCE such as an 

oven, stove or direct sunlight. 

• THE DOORS MUST CLOSE HERMETICALLY, check the magnetic gasket of 

the doors.

• LEVEL THE REFRIGERATOR, remove the wooden bases and adjust the 

leveling screws (

fi

 gure 1). 

• DO NOT OVERLOAD THE REFRIGERATOR, the circulation of cold air will 

be de

fi

 cient. 

• Set the TEMPERATURE control knob to MED (medium cold) and wait at least 

24 hours before making a new temperature change.

THE REFRIGERATOR WORKS FOR EXTENDED PERIODS

• Check that the CONDENSER IS FREE OF DUST AND LINT (

fi

 gure 1)

• AVOID OPENING THE DOOR CONTINUOUSLY or for prolonged periods. 
• DO NOT STORE HOT FOODS and keep them covered.

IF YOU HEAR STRANGE SOUNDS

• Check that there are NO OBJECTS OVER OR BEHIND THE REFRIGERTOR. 

• The COMPRESSOR DOES NOT WORK PROPERLY, it may be that a low 

voltage is present, verify the intensity of the light, if it is low this indicates that 

it has a low voltage, speak to your company of light to correct the power supply 

(

fi

 gure 1).

Before calling the technician

MAGNETIC GASKET

LEVELING SCREWS

CONDENSER

COMPRESSOR

IF AFTER FOLLOWING 

THESE INSTRUCTIONS, 

THE REFRIGERATION IS 

MALFUNCTIONING, PLEASE 

CONTACT OUR TECHNICAL 

SUPPORT CENTER

Figure 1

Procedimiento para limpieza de puertas y gabinetes con mancha de oxido Importante

Mantén el refrigerador en un ambiente  seco. Al haber acumulación de humedad, el metal 
se oxida y se produce herrumbre. 

Método de limpieza manual 

1. Humedezca una 

esponja en agua 

con detergente.

2. Use la 

ƐƵƉĞƌĮĐŝĞ

suave de la esponja 
para frotar sobre la 
mancha de oxido. 

El frote debe ser  

en el mismo 

Cuidado de su refrigerador

3. Use la 

ƐƵƉĞƌĮĐŝĞ

dura para frotar 
sobre la mancha de 
oxido. El frote debe 
ser en el mismo 

4. Enjuague la 

esponja con agua 
simple hasta eliminar 

el detergente.

. de R.L. de C.V

.

.

W11347727  Rev. A

STM W11202260 Rev. C

MX

AS8950G

1. Garantizar que la pestaña de la moldura este posicionada

    para arriba, de acuerdo con la image.

4. 

Accesorio de alambrón 

ĐĐĞƐŽƌŝŽƷƟůLJƉƌĄĐƟĐŽ

para acomodar productos

ĞŶϮĂůƚƵƌĂƐĚŝƐƟŶƚĂƐ͘

ENGLISH - 4

ESPAÑOL - 1

MANUAL W11347727 - W11354967.indd   1-2

MANUAL W11347727 - W11354967.indd   1-2

24/04/19   15:11

24/04/19   15:11

Reviews: