background image

Quick Start

D

ESCRIPTION

The ADTRAN 401 1 GE Micro ONT is an Optical Network 
Terminal (ONT). It is a member of the Micro ONT family 
supporting auto-detection of Active Ethernet and GPON network 
connections for use in point-to-point and point to-multipoint optical 
distribution networks (ODNs). 

Figure 1

 illustrates the key features on the Micro ONT.

Figure 1. Micro ONT Key Features

The table opposite provides descriptions for each feature number 
above.

LAN

FIBER

POWER

2

1

3

5

4

Fiber (FIBER)

GPON/Active Ethernet is supplied to the Micro ONT using an SC/
APC Fiber connection located on the rear of the unit.

Ethernet Interface (LAN)

The Micro ONT supports data service through one 10/100/
1000BASE-T Ethernet interface. 

Power

The power feed is +12 VDC from the included AC to DC Adapter. 
The adapter plugs into the PWR connector. The total power 
consumption is approximately 5 watts.

ONT Reset (RESET)

Refer to 

Figure 1

 for the location of the Reset button.

Reset the Micro ONT if you need to reboot the unit. The RESET 
button is accessed through an opening on the bottom of the unit. 
To reset the Micro ONT, insert a small pin (paper clip) into the 
RESET opening and hold the button down for 10 seconds.
The Micro ONT will automatically download the latest provisioning 
after the reset process has completed.

I

NSTALLATION

Before installing the Micro ONT, inspect it for damage. If damage 
has occurred during shipping, file a claim with the carrier and then 
contact ADTRAN. For more information, refer to the warranty.

Installation Guidelines

The following are guidelines for this installation.

Read all warnings and cautions before installing or servicing 
the Micro ONT.

Do not locate the Micro ONT in direct sunlight or next to any 
thermal obstructions.

When the SC/APC fiber connection is not in use, replacing the 
Protective Cover will help keep the optical connection clean.

This product should not come in contact with water or other 
liquids.

Number

Feature

1

Single GPON and Active Ethernet fiber interface with 
1.244 Gbps upstream and 2.488 Gbps downstream

2

10/100/1000BASE-T Ethernet Interface (LAN)

3

AC Power Adapter Input

4

Status LEDs

5

Reset Button

ADTRAN 401

Micro ONT

1 GE

September 2020

61287786F1-13A

P/N: 1287786F1

Summary of Contents for 401 1 GE Micro ONT

Page 1: ...ET button is accessed through an opening on the bottom of the unit To reset the Micro ONT insert a small pin paper clip into the RESET opening and hold the button down for 10 seconds The Micro ONT will automatically download the latest provisioning after the reset process has completed INSTALLATION Before installing the Micro ONT inspect it for damage If damage has occurred during shipping file a ...

Page 2: ...e following steps Step 1 Position the Micro ONT Step 2 Connect Ethernet Step 3 Connect Fiber Step 4 Connect 12 VDC Power Required Tools Standard technician tools and those listed below are required for installing the Micro ONT Optical power meter with wavelength filtering Fiberscope or videoscope For fiber optic connections the following is required ODC Fiber cleaning tool Installation Steps To in...

Page 3: ...hooting tips Problem Possible Solution The FIBER LED contin ues flashing Green Use an optical power meter to check the receiving power to see if it between 27 dbm and 8 dbm Reset the ONT using the Reset button If the ONT fails again replace the ONT with another unit The Power LED is Off Make sure the power cable connector is properly seated in the ONT power input Verify that the power adapter is p...

Page 4: ...ondensing MAINTENANCE The Micro ONT does not require routine hardware maintenance for normal operation We do not recommend that you attempt repairs in the field Obtain repair services by returning the defective unit to ADTRAN Refer to the warranty for further infor mation Field support for software is provided through upgrade facilities SAFETY AND REGULATORY Refer to the Safety and Regulatory Noti...

Reviews: