B
LUESOCKET
2135 A
CCESS
P
OINT
P/N 1700962F1
H
ARDWARE
The following items are included in your shipment:
•
Bluesocket 2135 Access Point (BSAP)
•
One plane bracket with hardware
-
Four expansion bolts with washers and nuts
-
Four hex cap screws with washers and lock washers
•
One pole mounting base with hardware
-
One hose strap
-
Four round head screws with washers and lock washers
•
Watertight PoE fitting
•
Grounding cable
A
NTENNAS
The BSAP 2135 provides six N-type antenna connectors (no integrated antennas are included). These
connectors support two internal 802.11 radios: one 2.4 GHz 802.11b/g/n radio and one 5 GHz
802.11a/n/ac radio. There are three antenna connectors for each band labeled
2.4GHz
and
5GHz
. A set
of six high-efficiency omnidirectional antennas can be ordered from ADTRAN for the BSAP 2135
(P/N 1700930F1, three 5 GHz, 7 dBi gain and three 2.4 GHz, 5 dBi gain).
Make a note of the 12-character MAC address and 14-digit serial number
listed on the back of the BSAP 2135 before mounting the AP to a wall or other
surface. This information will be required during configuration.
Grounding Point
Watertight
PoE Fitting
Antenna Connectors
C
ONFIGURING THE
BSAP’
S
IP A
DDRESS
U
SING THE
CLI
By default, DHCP is enabled on the BSAP 2135. However, if you need to statically configure the IP
address or statically configure AP discovery for the BSAP, follow these steps:
1. Ensure that the BSAP is connected to a controlling computer (using the provided RJ-45 Ethernet
cable).
2. Specify that the computer’s TCP/IP setting is
On
or
Enabled
by navigating to
Control Panel
>
Network Connections
and double-clicking the connection of your network interface card. Select
Internet Protocol (TCP/IP)
and select
Properties
. Then specify that the TCP/IP setting is enabled.
3. Set your PC to a static IP address of
192.168.190.2
with a subnet mask of
255.255.255.0
.
4. Next, access the BSAP’s command line interface (CLI) using an SSH client. Open an SSH
connection using the unit’s default IP address (
192.168.190.1
) and port
2335
connected to the
LAN1
port on the BSAP. To access the unit using vWLAN, and for more instructions about CLI
configuration, refer to the
Bluesocket vWLAN Administrator’s Guide
, available online at
https://supportforums.adtran.com
.
C
ONFIGURING THE
A
PPLICATION
More detailed documentation for configuring the BSAP 2135 is provided in the
Bluesocket vWLAN
Administrator’s Guide
, available online at
https://supportforums.adtran.com
.
FCC R
ADIO
F
REQUENCY
I
NTERFERENCE
This device complies with Part 15 of the Federal Communications Commission (FCC) rules. The
operation of this device is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received including interference that may cause undesired
operation.
T
HIRD
-P
ARTY
S
OFTWARE
The software included in the Bluesocket 2135 contains copyrighted software that is licensed under the
GNU General Public License (GPL). For a list of third-party software and their licenses, go to
http://www.adtran.com/software/EULA
. You can obtain the complete corresponding source code of such
software components from ADTRAN for a period of three years after our last shipment of this product by
sending a money order or check for $5 to:
ADTRAN, Inc, P.O. Box 933638, Atlanta, GA 31193-3638
Please write
GPL Source for product Bluesocket 2135
in the memo line of your payment.
This offer is valid to anyone in receipt of this information.
8
Copyright © 2015 ADTRAN, Inc. All Rights Reserved.
Quick Start Guide, 61700962F1-13B, May 2015
1
