background image

Quick Start Guide, 61700630E1-13D, February 2014

1

4

Copyright © 2014 ADTRAN, Inc. All Rights Reserved.

N

ET

V

ANTA

 4430 R

OUTER

P/N 1700630E1

G

ETTING

 S

TARTED

Two configuration methods are available for your NetVanta router:

Web-based graphical user interface (GUI)

ADTRAN Operating System (AOS) command line interface (CLI)

The GUI lets you configure the main unit settings and provides online guidance and explanations 
for each setting, and configuration wizards to help you get started. However, using the AOS CLI 
may be necessary for more advanced configurations. 

A

CCESS

 

THE

 GUI

You may access the GUI from any web browser on your network by following these steps:

1.

Connect the router to your PC using the 

ETH 0/1

 port on the front of the unit and an Ethernet 

cross-over cable.

2.

Set your PC to a fixed IP address of 

10.10.10.2

. To change your PC IP address, navigate to 

Computer

 > 

Control Panel 

Network Connections

 > 

Local Area Connection

 > 

Properties

 > 

IP (TCP/IP)

 and select 

Use this IP Address

. Enter these parameters:

IP Address: 

10.10.10.2

Subnet Mask: 

255.255.255.0

Default Gateway: 

10.10.10.1

You do not need to enter any domain naming server (DNS) server information. After the 
information is entered, select 

Ok

 twice, and close the Network Connections dialog box.

 

If 

you cannot change the PC’s IP address, you will need to change the unit’s IP address using 
the CLI. (Refer to the next two sections for instructions.)

3.

Open a web browser and enter the unit’s IP address in your browser address line as follows: 

http://10.10.10.1

. The default IP address is 

10.10.10.1

, but if you had to change the unit’s IP 

address using the CLI, enter that address in the browser line.

4.

You will then be prompted for the user name and password (the default settings are 

admin

 

and 

password

).

5.

The initial GUI screen appears. You can access initial setup information by selecting 

Setup 

Wizard

 from the menu on the left.

A

CCESS

 

THE

 CLI

Access the AOS CLI via the 

CONSOLE

 port, a Telnet session, or from the GUI. To establish a 

connection to the NetVanta router 

CONSOLE

 port, you need the following items:

PC with VT100 terminal emulation software

Straight-through serial cable with a DB-9 (male) connector on one end and the appropriate 
interface for your terminal or PC communication port on the other end

There are many terminal emulation applications available on the web. PuTTY, 
SecureCRT, and HyperTerminal are a few examples.

C

ONFIGURE

 Y

OUR

 A

PPLICATION

The applications you will need to configure vary by product and by network. Review the list of 
defaults for your unit before deciding what applications to configure. The following are some 
common applications that should be configured on startup. These are all available on 

ADTRAN’s 

Support Forum.

R

ESTORING

 F

ACTORY

 D

EFAULTS

On units that have a console port, you cannot restore the factory defaults, but must rather erase 
the device’s configuration and then reconfigure the unit to operate correctly for your network. To 
erase the unit’s current configuration, follow these steps:
1.

Access the unit’s CLI and enter 

enable

 at the 

>

 prompt.

2.

Enter 

erase startup-config

 at the 

#

 prompt. The device will have a blank configuration upon 

reboot.

3.

Enter 

reload

 at the 

#

 prompt to begin restarting the device. When prompted to save 

configuration, enter 

no

. When prompted to reboot, enter 

yes

.

4.

Upon reboot, you will have to reconfigure the unit using the 

CONSOLE

 port. Follow the 

steps outlined here or in the technical note, 

Accessing the Web Interface in AOS

 

at 

https://supportforums.adtran.com

.

Configuring T1 Access to a Remote Site 

Using PPP in AOS

 

Configuring Internet Access (Many to One NAT) with 

the Firewall Wizard in AOS

Configuring Port Forwarding in AOS 

Configuring QoS for VoIP in AOS

Configuring PPP in AOS

Configuring HDLC in AOS

Configuring Frame Relay in AOS

 

Configuring QoS in AOS 

Configuring DHCP Server in AOS 

Configuring a VPN Using Main Mode in AOS

 

Configuring a VPN Using Aggressive Mode 

in AOS

 

Important: 

For additional details on product features, specifications, 

installation, and safety, refer to 

NetVanta 4000 Series Hardware Installation 

Guide

 at 

https://supportforums.adtran.com.

.

N

ET

V

ANTA

 4000 S

ERIES

 D

EFAULTS

Feature

Default Value

IP Address

10.10.10.1

Username

admin

Password

password

HTTP Server

Enabled

Event History

On

IP Routing

Enabled

Reviews: