job
Aid
D
ESCRIPTION
The
Small
Form
‐
Factor
Pluggable
(SFP)
Gigabit
Ethernet,
Single
‐
Fiber
is
a
bidirectional
SFP
that
plugs
into
an
Optical
Line
Terminal
(OLT)
designed
to
accept
SFPs.
The
SFP
provides
a
single
optical
interface
to
the
GigE
physical
interface.
Installed
into
an
appropriate
OLT,
the
SFP
provides
a
Gigabit
Ethernet
interface
to
the
supporting
system.
NOTE
To
ensure
compatibility,
refer
to
the
documentation
provided
with
the
OLT.
NOTICE
In
a
deployment
consisting
of
an
OLT
with
a
1442180G2
SFP
installed;
the
Network
Unit
(ONT)
should
have
a
complementary
1442180G1
SFP
installed.
The
following
features
are
supported
on
the
SFP:
♦
1000Base
‐
LX
1490
nm
Transmitter
♦
1000Base
‐
LX
1550
nm
Receiver
♦
Optical
distance:
80
km
maximum
CAUTION
!
Due
to
compliance
certification
requirements,
only
SFPs
supplied
by
ADTRAN
should
be
used.
ADTRAN
cannot
certify
system
integrity
with
other
SFPs.
OLT
1442180G1
1442180G2
ONU
Rx: 1490 nm
Tx: 1550 nm
Rx: 1550 nm
Tx: 1490 nm
Small Form-Factor Pluggable
1490nm TX 1550nm RX 80km
Operational Specifications
♦
Optical
Specifications:
◊
Transmit
wavelength:
1490
nm
◊
Receive
wavelength:
1550
nm
◊
Optical
transmit
level:
–2
dBm
to
+3
dBm
◊
Optical
receive
level:
–25
dBm
to
–3
dBm
◊
Optical
distance:
80
km
◊
Optical
connectors:
LC
♦
Extended
Environmental
Support:
◊
Operational
temperature
range:
–40°C
to
+70°C
◊
Storage
temperature
range:
–40°C
to
+85°C
◊
Relative
humidity
to
95%,
noncondensing
I
NSTALLATION
Prior
to
installation,
inspect
the
SFP.
If
damage
has
occured
during
shipping,
file
a
claim
with
the
carrier,
and
then
contact
ADTRAN
Customer
Support.
For
more
infor
‐
mation,
refer
to
“Warranty”.
To
install
the
SFP
into
an
appropriate
module,
complete
the
following
steps:
1. Insert
the
SFP
into
the
SFP
cage
on
the
circuit
board
of
the
host
module
with
the
latch
handle
facing
outward.
Slide
the
SFP
all
the
way
into
the
cage.
NOTE
The
latch
on
the
SFP
is
for
removal
only.
When
removing
the
SFP,
rotate
the
latch
away
from
the
SFP,
the
SFP
should
slide
easily
out
of
the
cage.
2. Exert
adequate
pressure
to
ensure
the
SFP
is
completely
seated
in
the
SFP
cage.
3. Do
not
remove
the
connector
plug
until
the
optical
fiber
connection
is
made.
NOTICE
It
is
recommended
that
the
connector
plug
remain
on
whenever
the
transciever
optical
fiber
connector
is
not
inserted.
4. Continue
the
installation
and
turn
‐
up
of
the
host
module
using
the
instructions
in
the
Job
Aid
provided
with
the
module,
or
using
the
Installation
and
Maintenance
Practice
(I&M)
available
online
at
www.adtran.com.
CLEI: SOOTAK8J_ _
Product P/N: 1442180G2
Issue Date: November 2010
Document P/N: 61442180G2-22A
