background image

CHT-100 Cylinder Head Temperature Indicator 

Page 1 of 11

 

 

Aerospace Logic Inc. 

3150 Ridgeway Drive, Unit #43, Mississauga, Ontario, L5L 5R5, CANADA 

Tel. (905) 569-3887 | Fax. (416) 352-5854 | Email. sales@aerospacelogic.com 

www.aerospacelogic.com 

CHT-100 Operations & Installation Manual – Ver. 1.9 – June 5, 2003

 

 
 

 

All specification subject to change 

© 2002-2003 Aerospace Logic Inc.

 

 

CHT-100 Operations and Installation Manual 

 
 
 
 
 
 
 
 
 
 
 
 
 
 

READ THIS FIRST

 

 
 

Congratulations on the purchase of your CHT-100 Cylinder Head Temperature Indicator. 
This instrument is a complex precision instrument manufactured to exceed Airborne 
Equipment Standards DO-160D, DO-178B and TSO C43c standards. In order for your 
instrument to function correctly you will need to review the instructions in this brief 
manual. 
 
 
This document covers the following instrument models: 
 

  CHT-100-4 

4 Cylinder CHT 

  CHT-100-4V  4 Cylinder CHT with Voltmeter 

  CHT-100-6 

6 Cylinder CHT 

  CHT-100-6V  6 Cylinder CHT with Voltmeter 

 

This manual is certified for use with 

instrument serial number  

 

ASL000000 

 

Use of this manual with any other 

instrument voids all warranties and may 

result in damage to the instrument 

Summary of Contents for CHT-100












Reviews: