SITE SURVEY
AES KPX1200
AES KPX1200 STANDARD OPERATIONS
TIP:
If fitting this keypad as an independent system then no site survey is required.
If the keypad is included inside a callpoint then please follow the site survey details
included on the main product guide.
TIP:
Most technical calls received are due to installers using CAT5 or alarm cable
to power the unit.
NEITHER
are rated to carry enough power!
( 1.2amp peak )
Please use the following cable:
Up to 2 metres ( 6 feet )
–
Use minimum
0.5mm
2
( 18 gauge )
Up to 4 metres ( 12 feet )
–
Use minimum
0.75mm
2
( 16 gauge )
Up to 8 metres ( 24 feet )
–
Use minimum
1.0mm
2
( 14 / 16 gauge )
POWER CABLE
N/ O
C
N/ C
Normally Open
Common
Normally Closed
RELAY CONNECTIONS
* ALWAYS TEST THE UNIT ON SITE BEFORE INSTALLATION TO AVOID RESTOCKING FEES *
- Analog Keypad
MAINS
POWER
NEED MORE ASSISTANCE?
Please scan this QR Code to be
brought to our RESOURCES PAGE
where you can find all of our
guides and available resources.
RELAY 1
R2
12
.0
00
24v IN
EGRESS
RE
LAY
3
GROUND
+ -
N.C. COM
N.O.
N.C. / N.O.
DATA
I/O
EG
IN
N
.C
.
C
O
M
N
.O
.
K
or
A
O/
P
DU OU
T
DO
OR
SE
NS
(-) GN
D
O
/P
1
IN
HI
B.
IN
T
LO
CK
TA
M
PE
R
N.
C.
A
B
C
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
{1,2} 24v 2Amp
= Regulated PSU
(Pre-wired for inside an AES Intercom System)
{9,15} Egress for PTE (Push To Exit)
If you wish to make use of this feature you must wire your PTE switch using
terminals
9
&
15
marked as ‘
EG IN
’ and ‘
(-) GND
.
Note:
The egress feature on the keypad is designed to only activate
Output 1
. Ensure
that the entry you wish to gain access to via the PTE switch is connected to this output.
Programmable for Instant, Delay with Warning and/or Alarm Momentary or Holding
Contact for Exit Delay.
AES KPX1200 RELAY OUTPUT INFORMATION
{3,4,5} RELAY 1
=
5A/24VDC Max. N.C. & N.O. dry contacts.
1,000 (Codes) + 50 Duress Codes
{6,7,C} RELAY 2
=
1A/24VDC Max. N.C. & N.O. dry contacts.
100 (Codes) + 10 Duress Codes
(COMMON port is determined by the Shunt Jumper marked
as C on the diagram. Connect your device to N.C. and N.O. and then move the jumper to
the required position and test.)
{10,11,12} RELAY 3
=
1A/24VDC Max. N.C. & N.O. dry contacts.
100 (Codes) + 10 Duress Codes
{19,20} Tamper Switch
=
50mA/24VDC Max.
N.C. dry contact.
{A} BACK-LIT JUMPER
=
FULL/AUTO.
FULL
–
The keypad gives dim backlit in standby. It turns to full backlit when a button is pressed,
then back to dim backlit 10 secs after the last button is pressed.
AUTO
–
The backlit is
OFF
in standby. It turns to
FULL
backlit when a button is pressed, then
back to
OFF
10 seconds after the last button is pressed.
{B} ALARM OUTPUT SETTING
=
( RESOURCES PAGE - ADVANCED WIRING OPTIONS )
LED 1
=
RED
/
GREEN
. It lights up in
RED
while one of the outputs is inhibited. It is flashing during inhibition paused. It is
also the
Wiegand
LED for feedback indication and will light up in
GREEN
.
LED 2
=
AMBER
. It flashes in Standby. It shows the system status in synchronization with the beeps.
LED 3
=
RED
/
GREEN
. It lights up in
GREEN
for
OUTPUT 1
activation; and
RED
for
OUTPUT 2
activation.
SUPPLEMENT WIRING DIAGRAMS CAN BE
FOUND ON OUR RESOURCE PAGE.
1
2
3
( LEDs ABOVE KEYPAD FRONT )
OUTPUT 2
N.C.
|
N.O.
^MOVE JUMPER LINK^
NC
NO
COM
KEYPAD
RELAY
NC
NO
COM
SECONDARY
RELAY
MAGNETIC LOCK WIRING METHOD
NC
NO
COM
KEYPAD
RELAY
NC
NO
COM
SECONDARY
RELAY
STRIKE LOCK WIRING METHOD
MAX 24 VOLTS!
MAX 24 VOLTS!
MAGNETIC LOCK
STRIKE
LOCK
LOCK POWER SUPPLIES
ARE NOT INCLUDED AS
PART OF THE KIT.
* SOLD SEPARATELY *
* SOLD SEPARATELY *
MAINS
POWER
( LINKING WITH SECONDARY RELAY IS OPTIONAL FOR BOTH METHODS )
ALL THREE
OUTPUTS ARE
VOLT-FREE
CONTACTS.
STILL HAVING TROUBLE?
Find all of our support options such as Web Chat,
Full Manuals, Customer Helpline and more on
our website:
WWW
.
AESGLOBALONLINE
.
COM
KEEP POWER SUPPLY AS CLOSE AS POSSIBLE.
Did you know?
Extra
Prox cards
and
Prox Tags
can be purchased in packs of 10
& 50.
( PROX versions only )
