background image

Contact Information:

Customer Service:

Business (519) 650-5775

Fax (519)650-3773

Toll Free Telephone 1-877-650-5775

Toll Free Fax 1-800-327-5609

IMPORTANT: Save these instructions for the Local Electrical Inspector’s use.

INSTALLER: Please leave these instructions with this unit for the owner.

OWNER: Please retain these instructions for future reference.

SAFETY WARNING: Before servicing or cleaning the unit, switch the power

off at the service panel and lock out the service disconnect switch to prevent

power from being switched on accidentally. When the service disconnect

switch cannot be locked, securely fasten a prominent warning device, such

as a tag to the service panel.

Record the model and serial numbers before installing the Aga ventilation

hood. Both numbers are listed on the rating plate, located on the left wall of

the hood shell.

Model Number_______________________________

Serial Number_______________________________

INSTRUCTION & INSTALLATION MANUAL

36” & 48” VENTILATION HOOD

Please read entire instructions before proceeding.

Installation must comply with all local codes.

070208

C

Summary of Contents for VENTILATION HOOD















Reviews: