background image

www.airkinglimited.com

980051015 Rev B. 9-05

1 of 8

READ AND SAVE THESE INSTRUCTIONS

READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE OR MAINTAIN THE PRODUCT DESCRIBED.

PROTECT YOURSELF AND OTHERS BY OBSERVING ALL SAFETY INFORMATION. FAILURE TO COMPLY WITH

INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE!

RETAIN INSTRUCTIONS FOR FUTURE REFERENCE.

GENERAL SAFETY INFORMATION

When using electrical appliances, basic precautions

should always be followed to reduce the risk of fire,

electric shock and injury to person, including the following:

WARNING:

 

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK

AND INJURY TO PERSON, OBSERVE THE FOLLOWING:

1.

Read all instructions before installing or using fan.

2.

Use this unit only in the manner intended by the manufacturer.
If you have questions, contact the manufacturer.

3.

Before servicing or cleaning the unit, switch power off at service
panel and lock the service disconnecting means to prevent
power from being switched on accidentally. When the service
disconnecting means cannot be locked, securely fasten a
prominent warning device, such as a tag, to the service panel.

4.

Installation work and electrical wiring must be done by qualified
person(s) in accordance with all applicable codes and standards,
including fire-related construction.

CAUTION:

 

THIS FAN MUST NOT BE USED IN POTENTIALLY

DANGEROUS LOCATIONS SUCH AS FLAMMABLE, EXPLOSIVE,
CHEMICAL-LADEN OR WET ATMOSPHERES.

5.

Make certain that the power source conforms to the electrical
requirements of the fan.

6.

The fan must be hung with at least 7 feet of clearance from the
floor to the blades.

Models: 9800, 9805,

9810, 9815

Ceiling Fan

SAVE THESE INSTRUCTIONS

7.

Completely reassemble fan according to instructions before
reconnecting to power supply.

WARNING:

 

TO REDUCE THE RISK OF PERSONAL INJURY,

DO NOT BEND THE BLADE BRACKETS OR BLADES WHEN
INSTALLING THE BLADES, BALANCING THE BLADES, OR CLEANING
THE FAN. DO NOT INSERT FOREIGN OBLECTS IN BETWEEN THE
ROTATING FAN BLADES.

8.

This fan is not for use in wet or damp locations.

9.

Do not use fan outdoors and never locate the fan where it may
fall into a bathtub or other water container.

10. This unit must be grounded.

11. To avoid motor bearing damage and noisy and/or unbalanced

impellers, keep drywall spray, construction dust, etc. off power
unit.

12. DO NOT install or attach decorative elements or any other objects

onto the fan or fan blades.

WARNING:

 

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK,

DO NOT USE THIS FAN WITH ANY SOLID-STATE SPEED CONTROL
DEVICE.

IMPORTANT INSTRUCTIONS -

OPERATING MANUAL

Summary of Contents for Builder's Choice 9800









Reviews: