1
OVERVIEW
The
Trilogy
Networx
™
AL-IME2-EXP Expander
extends
the coverage area of version 2 series Gateways, allowing
control of up to its rated maximum of 63 Networx locks per
Gateway. Installation is simple, as the Expander only re-
quires a connection to an AC outlet.
AL-IME2-EXP
Expanders are cost-effective, easier to wire
than conventional Gateways, and feature a simplified 'Plug
and Play' setup where the Networx system automatically
identifies all newly powered Expanders and quickly deter-
mines the best wireless signal pathways. Up to 7 Expanders
can be added to one version 2 series Gateway.
Why use AL-IME2-EXP Expanders?
Less costly, Expanders can be used in place of addition-
al Gateways
Does not require network access / Ethernet cables
Extends wireless lock signal coverage
Reach otherwise troublesome locks in areas of insuffi-
cient signal strength
Allows for easier (flexible) positioning of version 2 Gate-
ways
Allows large area signal coverage with a single network
connection to the Gateway
Note:
Expanders are available in two different designs,
the
AL-IME2-EXP
and the
AL-IME2-PIE Plug-In Expander
(identical in operation, the compact
AL-IME2-PIE
plugs di-
rectly into a standard 120VAC un-switched/uninterruptable
wall outlet).
Version
2
The
AL-IME2-EXP
" version 2" Expanders (notice the "
2
"
in the model name) are the next generation of Networx wire-
less devices. Because
AL-IME2-EXP
Expanders
only
work with version 2 Gateways, a version 2 Gateway must be
installed and operational in your system for
AL-IME2-EXP
Expanders to function (
AL-IME2-EXP
Expanders cannot
communicate with older "non-version 2" Gateways).
Note:
Although the version 2 Gateways and
AL-IME2-
EXP
Expanders CAN be mixed into an existing system
that includes older "non-version 2" Gateways,
at least one
new version 2 Gateway must be up and running before an
AL-IME2-EXP Expander can be used
.
IMPORTANT:
DL-Windows version 5.4.2
or later is re-
quired to support version 2 Gateways and Expanders.
The
AL-IME2-EXP
Expander is compatible with Alarm
Lock and Continental Access products. Refer to the docu-
mentation supplied with your software for integration details.
AL-IME2-EXP SPECIFICATIONS
NETWORK RANGE
Gateway/Expander to Locks: Clear field range 500'.
Typical indoor range: Networx 75-175'; ArchiTech Networx:
50-125'.
Note:
Actual range varies with building con-
struction.
AL-IME2-EXP Expander
Installation Instructions
© ALARM LOCK 2018
WI2156BLF 1/18
Gateway/Expander to Expander: Clear field range 500'.
Typical indoor range, 75- 175'.
Note:
Actual range varies
with building construction.
AL RADIO LINK
900 MHz GFSK
50 Channels
10mW power output
POWER
- Provided by UL Listed Class 2 Transformer
Peak Supply Current: 150mA
Input Voltage: 5 - 6VAC
Includes one (1) 6VAC External Power Supply
ENVIRONMENTAL
Operating Temperature: -20
˚
to 60
˚
C (-4
˚
to 140
˚
F)
Storage Temperature: -40
˚
to 85
˚
C (-40
˚
to 185
˚
F)
PHYSICAL
Enclosure Size: 4.5"H x 6.0"W x 1.94"D
Weight: 0.5lbs.
EXPANDER LOCATION GUIDELINES
Once your version 2 Gateway location has been selected,
the next step is to determine where to mount the Expander.
However, the following must be taken into consideration:
Generally, the Expanders should be within approximately
75 feet (radially) from the Gateway or another Expander
Expanders should be located within 100 feet (radially) from
the intended wireless lock locations
Open areas will increase range while concrete building
construction, walls, ceilings and narrow corridors will
decrease range
ArchiTech series locks generally have shorter range to/
from an Expander
Select a location that allows access to the power wires
running from the 6VAC power transformer (supplied)
Expanders should be mounted in elevated areas; however
mounting in a drop ceiling can adversely affect signal
strength
Preferred mounting position = 6 to 12" below ceiling
Expanders must be mounted vertically; horizontal "flat"
mounting of the Expander should be specifically avoided
Although wood and wallboard construction can have little
effect upon signal strength, concrete or brick can reduce
signal strength by up to 35%. Steel-reinforced concrete or
metal lath and plaster can reduce signal strength as much
as 90%!
Do NOT mount close to electrical wiring or other metal
obstructions such as pipes or conduits
Installing in computer closets or server rooms can nega-
tively impact signal strength
Helpful
Tips
The
AL-NSM
Networx Signal Meter and the
AL-NSG
Networx Signal Generator can assist with identifying
345 Bayview Avenue
Amityville, New York 11701
For Sales and Repairs 1-800-ALA-LOCK
For Technical Service 1-800-645-9440
or visit us at
http://tech.napcosecurity.com/
(Note: Technical Service is for security professionals only)
Publicly traded on NASDAQ Symbol: NSSC
