THIS PRODUCT CONTAINS ELECTRONIC COMPONENTS WHICH RE-
QUIRE A DEFINITE GROUND. PROVISIONS ARE MADE FOR CONNEC-
TION OF THE GROUND. A DEDICATED GROUND FROM THE MAIN
POWER SUPPLY OR AN EARTH GROUND MUST BE PROVIDED.
I
F
A
“1
F
LASH
”
ERROR
CODE
OR
AN
“E
C
”
HTR
TOO
LARGE
ERROR
IS
ENCOUNTERED
ON
STARTUP
,
VERIFY
THAT
THE
ELECTRIC
HEATER
DIP
SWITCHES
HAVE
BEEN
SET
TO
THE
APPROPRIATE
HEATER
SIZE
.
S
EE
PAGES
7
AND
8
FOR
THE
HEATER
KIT
AIRFLOW
DELIVERY
AND
DIP
SWITCH
SETTINGS
.
NOTICE
I
NTRODUCTION
This booklet contains the installation and operating instruc-
tions for your modular blower cabinet. All warnings and pre-
cautions within this booklet must be observed. Improper in-
stallation can result in unsatisfactory operation or dangerous
conditions and void the warranty. Read this booklet and any
instructions packaged with accessories prior to installation.
Give this booklet to the user and explain its provisions. The
user should retain this booklet for future reference.
NOTE:
Upon start up in communicating mode the
circuit
board will display a “1 Flash” error code on the diagnostic
LED and an “Ec” HTR TO LARGE error at the communi-
cating display. This is an indication that the dip switches on
the control board need to be configured in accordance
with the Electric Heating Airflow Table on page 7 of this
manual. Configuring the dip switches and resetting power
to the unit will clear the error code.
E
LECTROSTATIC
D
ISCHARGE
(ESD) P
RECAUTIONS
NOTE:
Discharge body’s static electricity before touching
unit. An electrostatic discharge can adversely affect electrical
components.
Use the following precautions during modular blower instal-
lation and servicing to protect the integrated control module
from damage. By putting the modular blower, the control,
and the person at the same electrostatic potential, these steps
will help avoid exposing the integrated control module to elec-
trostatic discharge. This procedure is applicable to both in-
stalled and uninstalled (ungrounded) blowers.
1. Disconnect all power to the blower. Do not touch the
integrated control module or any wire connected to the
control prior to discharging your body’s electrostatic
charge to ground.
2. Firmly touch a clean, unpainted, metal surface of the
modular blower near the control. Any tools held in a
person’s hand during grounding will be discharged.
MBVC
BLOWER CABINET
INSTALLATION INSTRUCTIONS
© 2009-2010 Goodman Manufacturing Company, L.P.
5151 San Felipe, Suite 500, Houston, TX 77056
www.goodmanmfg.com -or- www.amana-hac.com
P/N: IO-344C
Date: November 2010
3. Service integrated control module or connecting wiring
following the discharge process in step 2. Use caution
not to recharge your body with static electricity; (i.e.,
do not move or shuffle your feet, do not touch
ungrounded objects, etc.). If you come in contact with
an ungrounded object, repeat step 2 before touching
control or wires.
4. Discharge your body to ground before removing a new
control from its container. Follow steps 1 through 3 if
installing the control on a blower. Return any old or
new controls to their containers before touching any
ungrounded object.
I
MPORTANT
N
OTE
TO
THE
O
WNER
REGARDING
P
RODUCT
W
ARRANTY
Your warranty certificate is supplied as a separate document
with the unit installed by your contractor. Read the limited
warranty certificate carefully to determine what is and is not
covered and keep the warranty certificate in a safe place. If
you are unable to locate the warranty certificate please con-
tact your installing contractor or contact customer service
(877-254-4729) to obtain a copy.
IMPORTANT:
To register your Goodman® brand unit, go to
www.goodmanmfg.com. Click on the word “Warranty” located
on the left side of the home page. Next, click on the word
“Product Registration” located on the left side of the War-
ranty page and complete the forms in the manner indicated
on the Product Registration page.
To register your Amana® brand unit, go to www.amana-
hac.com. Click on the word “Warranty” located on the top
right of the home page. Next, click on the word “Product
Registration” located on the left side of the Warranty page
and complete the forms in the manner indicated on the Prod-
uct Registration page.
Product limited warranty certificates for models currently in
production can be viewed at www.goodmanmfg.com or
www.amana-hac.com. If your model is not currently in pro-
duction or does not appear on the website, please contact
your installing contractor or contact customer service (877-
254-4729) to obtain a copy of your warranty certificate.
Each product overview page contains a Product Warranty
link; by clicking on it you will be able to view the limited war-
ranty coverage for that specific product. To view warranty
registration information, click on the Product Warranty text
on the left navigation panel on the home page of each web-
site. The Online Product Registration pages are located in
this same section.
C
HECKING
P
RODUCT
R
ECEIVED
Upon receiving the unit, inspect it for damage from shipment.
Claims for damage, either shipping or concealed, should be
Summary of Contents for MBVC
Page 14: ...14 APPENDIX A ...
