1 7/8
INSTALLATION INSTRUCTIONS
1. Remove cover by removing (2) tamper-proof-screws using security wrench
supplied. Pull cover directly toward you.
IMPORTANT
: Save security wrench.
2.
Dryers should be placed at least 2 feet (61cm) apart and at least 12” (30cm) from wash-
basin. Do not install dryer over washbasin. Automatic dryers should be at least 18” (46cm)
above any projection which may interfere with the operation of the automatic sensor.
Hold the backplate to the wall at the suggested mounting height. Measure from bottom edge
of
backplate
to the
floor (Ref. Dimension “A”, Fig. 1):
CHILDREN
MEN
WOMEN
(depends on age)
DISABLED
Hand -
44” (112cm)
42” (107cm)
32 to 42” (81-107cm)
36” (91cm)
Hair
- 74" (187cm)
68" (172cm)
48" to 68" (121-172cm)
48" (121cm)
3.
Mark the locations of the four mounting holes and the conduit entrance location on the wall.
(The conduit entrance is the proper hole diameter for 1/2 inch (13mm) conduit.)
4.
Fasten the backplate to the wall where previously marked.
RECOMMENDATION:
Wood wall –
No. 14 (M6) wood screws, 2 3/4” (70mm) long
Cement or brick –
1/4” (M6) stud expansion bolts, 3” (76mm) long
Hollow wall –
1/4” (M6) toggle bolts, length depends on wall thickness
5. Run service wire to the dryer location and connect to lead wires.
IMPORTANT: All units must be supplied with 3 wire service. Use No. 12 or 14 wire as
required by local electrical code. The ground wire must be connected to the dryer ground
screw. Unit must be installed by a qualified, licensed electrician.
CONNECT TO A DEDICATED CIRCUIT NOT TO EXCEED 20 AMPS.
Dryers located in shower rooms or other wet locations should be equipped with ground fault
interrupter(s).
6.
Carefully
replace the cover using (2) tamper-proof screws supplied. Apply a bead of caulk
around edges of cover to wall.
A
DVANTAGE
SERIES
MFD by AMERICAN DRYER, INC.
33067 INDUSTRIAL ROAD, LIVONIA, MI 48150, U.S.A.
Revised July 2013
A
DVANTAGE
DRYER LIMITED WARRANTY
All parts are warranted to the original consumer purchaser to be free from defects
in material and workmanship for a period of five (5) years from the date of purchase
from manufacturer. All models outside of the U.S.A., one (1) year. We will replace
FREE OF CHARGE, during the warranty period, any warranted part which proves
defective in material and/or workmanship under normal installation, use, and service,
excluding normal wear. Replacement parts can be obtained by returning the part,
TRANSPORTATION CHARGES PREPAID. You must notify factory prior to returning
part or dryer. Any damage to this dryer as a result of misuse, abuse, neglect, accident,
improper installation, unauthorized repairs, or any other use violative of instructions
furnished by us, WILL VOID THIS WARRANTY.
THIS LIMITED WARRANTY IS THE
SOLE WARRANTY ON OUR PRODUCTS, AND WE DISCLAIM AND EXCLUDE ANY
AND ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
OUR LIABILITY SHALL NOT EXCEED IN ANY EVENT THE REPLACEMENT OR SALE
PRICE OF THE ALLEGEDLY NONCONFORMING PRODUCT AND SHALL EXCLUDE
LABOR CHARGES. TO THE EXTENT PERMITTED BY LAW WE SHALL NOT BE
LIABLE FOR ANY LOSS, COST, EXPENSE, OR INCIDENTAL OR CONSEQUENTIAL
DAMAGES OF ANY KIND, WHETHER BASED UPON WARRANTY (EXPRESS OR
IMPLIED), CONTRACT, NEGLIGENCE OR STRICT LIABILITY AND ARISING IN
ANY WAY IN CONNECTION WITH THE DESIGN, MANUFACTURE, SALE, USE OR
REPAIR OF THE PRODUCT.
O
WNER
’
S
M
ANUAL
A
DVANTAGE
S
ERIES
H
AND
D
RYERS
I
MPORTANT
:
H
AVE
M
ODEL
& S
ERIAL
N
O
. R
EADY
M
ODEL
#______ S
ERIAL
#______
F
IGURE
1 -
D
RYER
M
OUNTING
(48mm)
(208mm)
6 3/16
7/8 (22mm) DIA. IN-WALL
& SURFACE CONDUIT
ENTRANCES
MOUNTING HOLES FOR
1/4” (M6) DIA. SCREWS
(227MM)
8 15/16
7/16
(11mm)
“A”
8 7/16
(214mm)
FLOOR
7/16
(11mm)
™
Failure to disconnect the power source before installation or servicing can result in serious
injury or death from electrical shock.
DANGER: Disconnect Power Before Servicing
improper installation or service.
WARNING:
