background image

American Dryer Corporation

88 Currant Road

Fall River MA 02720-4781

Telephone: (508) 678-9000  /  Fax: (508) 678-9447

e-mail: 

techsupport@amdry.com

www.amdry.com

ML-55II Installation Manual

Phase 7, Non-Coin

ADC

 Part No. 113345

Warning: 

 For your safety the information

in this manual must be followed to

minimize the risk of fire or explosion or to

prevent property damage, personal injury

or death.

— Do not store or use gasoline or other flam-

mable vapors and liquids in the vicinity of

this or any other appliance.

What To Do If You Smell Gas

• Do not try to light any appliance.

• Do not touch any electrical switch; do

not use any phone in your building.

• Clear the room, building or area of all

occupants.

• Immediately call your gas supplier from

a neighbor’s phone.  Follow the gas

supplier’s instructions.

• If you cannot reach your gas supplier,

call the fire department.

— Installation and service must be performed

by a qualified installer, service agency or

the gas supplier.

Avertissement:

  Assurez-vous de bien

suivre les instructions données dans cette

notice pour réduire au minimum le risque

d’incendie ou d’explosion ou pour éviter

tout dommage matériel, toute blessure ou

la mort.

— Ne pas entreposer ni utiliser d’essence ni

d’autres vapeurs ou liquides inflammables

à proximité de cet appareil ou de tout autre

appareil.

Que Faire Si Vous Sentez Une

Odeur De Gaz

• Ne pas tenter d’allumer d’appareils.

• Ne touchez à aucun interrupteur.  Ne

pas vous servir des téléphones se

trouvant dans le bâtiment.

• Évacuez la pièce, le bâtiment ou la

zone.

• Appelez immédiatement votre

fournisseur de gaz depuis un voisin.

Suivez les instructions du fournisseur.

• Si vous ne pouvez rejoindre le

fournisseur de gaz, appelez le service

des incendies.

— L’installation et l’entretien doivent être

assurés par un installateur ou un service

d’entretien qualifié ou par le fournisseur de

gaz.

Summary of Contents for ML-55 Phase 7



























Reviews: