background image

1

   M965985 (11/18)

© 2018 AS America Inc.

Installation Instr

uctions

Certified to comply with ASME A112.18.1

© 2018 AS America, Inc.

NOTE TO INSTALLER: Please give this manual to the customer after installation.

To learn more about American Standard Selectronic

®

 Products visit our website at: 

www.americanstandard-us.com

or e-mail us at: 

CRTTEAM@lixilamericas.com

For Parts, Service, Warranty or other Assistance, 
please call (844) CRT-TEAM / (844) 278-8326  (In Canada: 1-800-387-0369)
                                                                  

(In Toronto Area only: 1-905-306-1093)

Paradigm

 Selectronic

®

 Integrated  

Faucet with Optional Above-Deck Mixing  

& SmarTherm

®

MODEL NUMBERS

7025.1xx 702B.1xx
7025.2xx 702B.2xx
7025.3xx 702B.3xx

CAUTION: Use only American Standard supplied  
transformers and cable sets. Using non-AS supplied  
cables, or cutting, splicing or modifying any components  
will void the warranty.

Product No’.s & Options 

      2

Specifications 

 

 

      3

Faucet Installation 

 

      3

Electrical Installation   

      4-5

FAQ’s / Troubleshooting 

      9

Parts  

         

 

      10

Start-up / Maintenance  

      6-8

Summary of Contents for Paradigm Selectronic 7025.1 Series










Reviews: