background image

Installation Instr

uctions

In

s

ta

ll

a

ti

o

n

 I

n

s

tr

u

c

ti

o

n

s

(In Toronto Area only: 1-905-3061093)

SELECTRONIC™

Proximity Infection

Control Faucet

Certified to comply with ASME A112.18.1M

© 2011 American Standard

To learn more about American Standard Faucets visit our website at: 

www.us.amstd.com 

or U.S.

customer's e-mail us at: 

sensor@americanstandard.com

For Parts, Service, Warranty or other Assistance, 
please call

 

(855) 752-9259 (In Canada: 1-800-387-0369)

NOTE TO INSTALLER: Please give this manual to the customer after installation.

(In Toronto Area only: 1-905-3061093)

M 9 6 5 119   R E V.  1. 3  

Product No.'s & Options

Specifications

How to Install

Electrical Hook-up

Maintenance

FAQ,s

Replacement Parts

1

2

2-3

4-6

7-8

9

10

6055 / 6056 / 6057 Infection Control Faucet shown Installed on

American Standard 9118.111 Infection Control Sink

6055.193
6056.193
6057 

MODEL NUMBERS

.193

CAUTION:

  Use only American Standard 

supplied cable sets. Using non-AS supplied 
cables, or cutting, splicing or modifying any 
components will void the warranty.

Summary of Contents for SELECTRONIC 6055.193












Reviews: