X000-000
READ THIS BEFORE YOU BEGIN
Look over this Instruction Sheet carefully before you begin building. Following
the assembly instructions and “TEST-FIT” the parts without cementing. This
will familiarize you with the location of the parts.
For the best results, the various sub-assemblies and components should be
painted before any “CHROME” parts are attached. For example: When attaching
"NON-CHROME" engine parts, it is best to cement them in place and paint
as a unit, “CHROME” PARTS ARE INDICATED BY (C).
AMT kits are molded from the finest high-impact styrene plastic. Use only
paint and cement made for styene. Trim excess plastic from parts before
joining. When attaching “CHROME” or painted parts, scrape plating or paint
away where parts are to be joined. Cement all parts unless otherwise indicated
by the instructions. Use just enough cement to join parts and be careful not
to smear cement on exposed surfaces.
Built according to the instructions on this sheet, you should have no trouble
assembling your kit. Just follow the numbers as the instructions are numbered
in order of assembly.
1
31
1
19
1
13
1
1
6
6
7
8
5
4
3
3
9
9
11
12
29
25
30
26
22
20
21
19
16
15
14
27
28
2
10
10
13
17
18
31
23
24
ENGINE BLOCK
(2 pcs.)
1
RIGHT
REAR SPRING
SUSPENSION
FILTER
(2 pcs.)
STARTER
13
2 METAL AXLES
13
EXHAUST
BRACKET
FAN BELT
18
WATER PUMP
BELT
17
LICENSE PLATE
BREATHER
REAR
CROSSMEMBER
3 ROCKER ARM COVERS
OIL FILLER CAP
MOTOR MOUNT
FUEL PUMP LINE
FUEL PUMP
EXHAUST TURBINE
12
4 BACKING PLATES
12
4 SHOCKS
FREON COMPRESSOR
2 FRONT CAB MOUNTS
LENSES TO BE USED
2 TAILLIGHTS
Amber
RED
2 FENDER
REFLECTORS
2 SIDE REFLECTORS
2 FOG LIGHTS
5 CAB LENSES
EXTERNAL OIL LINE
ENGINE LEFT SIDE
2 FRONT OUTER WHEEL FLANGES
4 REAR OUTER WHEEL FLANGES
4 TIRES
4 REAR INNER WHEEL FLANGES
4 REAR BRAKE DRUMS
4 ASSEMBLED REAR WHEELS
4 REAR WHEELS
4 TIRES
4 HUB COVERS (C)
2 FRONT TIRES
2 FRONT INNER WHEELS (C)
ALTERNATOR
15
2 TAILLIGHTS
(Red)
DIPSTICK
14
4 ASSEMBLED REAR WHEELS
UPPER OIL COOLER
(2 pcs.)
6
INTER AXLE
DRIVESHAFT
ALTERNATOR BELT
16
TAILLIGHT BEZEL
INTAKE PIPE
(To Compressor Turbine)
AFTERCOOLER
COMPRESSOR TURBINE
11
6 AIR CHAMBERS
11
2 FRONT SPRINGS (Left and Right)
2 A I R C Y L I N D E R S
(One each side)
4
C E N T E R A X L E G E A R B OX
(2 pcs.)
C E N T E R A X L E
(2 pcs.)
F R O N T T R A C K B A R (Short)
2 ANTI-SKID CONTROLS
(Left and Right)
4
BOGIE CROSSMEMBER
MID CROSSMEMBER
(3 pcs.)
NOTE:
(Remove
pin)
NOTE: Cut centers from tires and snap tires over wheels.
NOTE: 2 parking brake chambers
go to rear axle backing plates only.
T R A N S M I S S I O N
(2 pcs.)
3
L E F T R E A R S P R I N G
S U S P E N S I O N
EXHAUST MANIFOLD
9
OIL PAN
2
CROSS TUBE
2
REAR CAB SUPPORT
E X H A U S T O U T L E T
10
2 PARKING BRAKE CHAMBERS
FAN
19
OIL COOLER
7
7
REAR ENGINE
CROSSMEMBER
BRACKET
(One each side)
2
TRANSMISSION
SUPPORT
WATER OUTLET
FRAME (Left)
FRONT COVER
5
5
FRAME (Right)
WATER MANIFOLD
8
REAR TRACK
BAR (Long)
REAR AXLE
(2 pcs.)
BACK UP LIGHT
(Clear)
8
REAR ENGINE
CROSSMEMBER
FUEL FILTERS
