background image

  Belonging  to

To protect your family

GS911K - 

V. 14

Household gas  detector

Important: Assembly / maintenance of the appliance must be carried out by qualified personnel and in
accordance with applicable laws and regulations.
The manufacturer assumes no responsibility for the use of products that have to comply with particular
environmental and / or installation standards.

Important note
Before connecting the equipment, it is recommended that you read the instruction manual carefully and
keep it for future reference. It is also recommended to perform the electrical connections correctly as
per enclosed drawings, observing the instructions and the Standards.
N.B. Refer to the documentation in all cases where the symbol is on the side

Channel:  Beinat  gas  solutions

Electric connections also available on

CONFORMITY

Installation and user
guide

EN 50194
EN 50270

CEI 216-3

EN 61010-1

Installation  EN 60079-29-2

   Reports issued by     TUV Italia

230 VAC

230 VAC

The elegance and the prestige, that have always made BEINAT S.r.l stand out from its competitors,
together with the concept of home fitness comes the household gas detector GS911K detects through
the catalytic sensor , the presence of explosive gas such as: Methane or LPG.

Gas detection

The detector is tested and calibrated to  10% of L.E.L.

Through  the built-in relay, the GS911K can  activate: solenoid  valves, sirens, and any other device
alarm.
A series of technical features make this gas detector extremely versatile, reliable, accurate, and safe.
through an  internal jumper it is possible to select the relay  impulse functioning, to  connect manual
reset solenoid valves, or the continuous functioning, to activate class “A” solenoid valves and sirens.
The relay, free of voltage, allows installation of multiple detectors on a single solenoid valve ensuring
control of multiple dangerous environments.

The  detector  is  complete  with  a  special  circuit  that  controls  the  catalytic  sensor’s  efficiency
level
, and signals any possible fault.
These technical features make the detector ideal for the safety of civil environments according to
EUROPEAN STANDARD.

Summary of Contents for Beinat GS911K









Reviews: