background image

-1- 

 

 

 

ARKBIRD  is  a  high-accuracy  autopilot  designed  for  fixed-wing.  It  can  superimpose  OSD  (On  Screen  Display) 

data on videos and at the same time control the balance, the return and many other maneuvers of your aircraft 

with high precision. 

The  perfect  auto-stabilization  system and  a  plug-and-play  design  free  you  from  worries  and  inconveniences 

and enjoy the beauty of FPV in an instant.   

Arkbird OSD 2.0 LITE Includes

 

      1. High accuracy air-speed meter interface; with air-speed and ground speed control and protection. 

      2. New design of shell and internal framework; flight performance optimized. 

      3. 7 input channels and 7 output channels; with stability augmentation output on the PTZ. 

      4. Flap can be intelligent controlled by speed , channel1-7 (aileron-flaps) mix-control selectable; with slow 

release function, flap value can be displayed on the OSD. 

      5. More ways of mixed control include delta wing and V-tail wing, and Bi-motor plane, Bi-motor flying wing 

and butterfly brake (mixed control of 1247channel). 

      6. Analog RSSI port and PPM port; support Arkbird 433 10RSSI single wire transmission. 

      7. Supports Arkbird GCS

Ground Control System

Support the import and export of waypoint table; 

multi-language. track replay;(refer to "Arkbird GCS &Two Planes' Formation Flight manual") 

 

8 Basic functions Escorts your flight

 

1. Function all in one broad, on broad IMU (Inertial measurement unit), OSD (On Screen Display), barometer 

Attitude  sensor,  12V-5V  regulation  chip,  “ESC  +  voltage  regulation”  dual  power  supply.  Industrial  reliable 

designed. 

2. Plug & Play design, no needed to weld any wire. 

3.Can be installed flatwise or sidewise, suitable for small aircraft. 

4. Intelligent PID controller. Easy to adjust. 

Summary of Contents for OSD 2.0





























Reviews: