2000W
FIREPLACE HEATER
wall mountable wItH curved svelte tempered glass panel
Dekkar
User ManUal
FOR PERSONAL INDOOR USE ONLY
WARNING!
To Reduce The RIsk of fIRe, elecTRIc shock,
oR peRsoNAl INjuRy, ReAd, uNdeRsTANd
ANd folloW INsTRucTIoNs befoRe
usING ThIs heATeR
Keep this manual in a safe place for future reference
EFH432
Arlec guarantees this product in accordance with the Australian
Consumer Law.
Arlec also warrants to the original first purchaser of this product
(“you”) from a retailer that this product will be free of defects
in materials and workmanship for a period of 12 months from
the date of purchase; provided the product is not used other
than for the purpose, or in a manner not within the scope of the
recommendations and limitations, specified by Arlec, is new and
not damaged at the time of purchase, has not been subjected
to abuse, misuse, neglect or damage, has not been modified or
repaired without the approval of Arlec and has not been used for
commercial purposes (“Warranty”).
If you wish to claim on the Warranty, you must, at your own
expense, return the product, and provide proof of original purchase
and your name, address and telephone number, to Arlec at the
address below or the retailer from whom you originally purchased
the product within 12 months from the date of purchase.
Arlec will (or authorise the retailer to) assess any claim you may
make on the Warranty in the above manner and if, in Arlec’s
reasonable opinion, the Warranty applies, Arlec will at its own
option and expense (or authorise the retailer to) replace the
product with the same or similar product or repair the product and
return it to you or refund the price you paid for the product. Arlec
will bear its own expenses of doing those things, and you must bear
any other expenses of claiming on the Warranty.
The Warranty is in addition to other rights and remedies you may
have under a law in relation to the product to which the Warranty
relates.
Our goods come with guarantees that cannot be excluded under
the Australian Consumer Law. You are entitled to a replacement
or refund for a major failure and for compensation for any other
reasonably foreseeable loss or damage. You are also entitled
to have the goods repaired or replaced if the goods fail to be of
acceptable quality and the failure does not amount to a major failure.
TechNIcAl specIfIcATIoNs
WARRANTy
CPIN002812/2
opeRATIoN
4
The appliance can be operated either by the switch located on the top right hand side of
the fire or by supplied remote control.
The Main power ON/OFF switch must be first switch on to operate the appliance.
MANuAl opeRATIoN
1. The switches are located at the top right hand side of the appliance.
2. Press once the Main power ON/OFF switch to turn on the appliance.
3. Press once the O/I button to turn on the flame effect; press again to switch off the
flame effect. A red indicator light will appear to indicate that the function is ON.
4. Press the O/I button for 3 seconds this will operate the dimmer mode.
5. Press once the 1000W button for the low heat settings; press again to switch off
the heat setting.
A red indicator light will appear to indicate that the function is ON.
6. Press once the 2000W button for the high heat settings; press again to switch off
the heat setting. A red indicator light will appear to indicate that the function is ON.
ReMoTe opeRATIoN
1. The Main power ON/OFF switch must be first switch on.
2. It takes some time for the receiver to respond to the transmitter.
Do not PRESS the buttons more than once within two seconds for correct operation.
3. Press once the button ON/OFF on the remote control this turns ON/OFF the appliance
and fire effect.
4. Press once the 1000W button for the low heat settings; press again to switch off
the heat setting.
5. Press once the 2000W button for the high heat settings; press again to switch off
the heat setting.
6. Press the DIMMER button for operate the dimmer mode.
sAfeTy cuT-off
• This appliance is fitted with a safety cut-off which will operate if the heater overheats
(eg. due to blocked air vents). For safety reasons, the heater will NOT automatically
reset.
• To reset the appliance, disconnect the appliance from the mains supply for at least
30 minutes. Reconnect the supply to the mains and switch on the appliance.
ReplAcING The flAMe effecT lAMp
Warning – Always disconnect from the power supply before removing bulb.
Warning – The bulbs reach high temperatures during operation. Allow the bulbs to cool
down after switching off the appliance before changing lamps.
Note:
Two people will be required for this process.
• It is recommended that the heater is carefully removed from the wall and laid on its back
in order to replace the lamp.
• Gently slide the front glass panel towards the top of the heater and remove. Store the glass
safely out of the way whilst the bulb is replaced so that it does not get damaged.
• At the bottom of heater, there is a lamp cover fixed by eight Philip’s head screws, remove
the eight screws and lift off the lamp cover (Fig.5).
• For access to the bottom bulbs, carefully slide the flexible rotisserie to one side ensuring
that the rubber grommet is not lost (Fig.6).
• Remove the defective bulb by unscrewing it.
• Replace with a G9 type globes, rotating it. Take care not to over-tighten the bulb.
• Refit the rotisserie making sure that the rubber grommet is carefully pushed into the slotted
hole on the axial bracket.
MAINTeNANce & cleANING
5
1. Before cleaning, turn off the heater, unplug the power cord and allow the heater to cool.
2. Do not immerse cord, plug or heater into water or other liquid or pour water or other liquid
over the heater.
3. Use a vacuum cleaner to remove dust and dirt from air openings.
4. Clean exterior surfaces using a solution of water and mild detergent with wrung out damp
sponge. Use and wring out the damp sponge and wipe the exterior surface again.
Finally wipe with a dry cloth.
Allow sufficient time to dry before plugging electrical cord into outlet.
5. The tempered glass front panel can be clean with glass cleaner detergents.
6. Any other servicing should be performed by an authorised service representative.
Do not use the heater if it has malfunctioned or become damaged in any way.
fig. 6
fig. 5
Model
efh432
Max heater Power
2000W max
Rated Frequency
50hz
Voltage
220-240V~
Bulb Wattage
40W max/bulb
(3 bulbs)
Bulb Size & Type
G9 halogen type
CPIN002812/2
For all Sales & Warranty enquiries
Arlec Australia Pty. Ltd. ACN 009 322 105
(“Arlec”) gives the Warranty.
Building 3, 31 – 41 Joseph Street, Blackburn North, Victoria, 3130
Blackburn North LPO, P.O. Box 1065, Blackburn North, 3130
Customer Service: (03) 9982 5111
New Zealand Toll Free: 0800 003 329
Email: custservice@arlec.com.au
useR MANuAl
