background image

 

 

SERIES 300 
Quick Connect Input and Output Power Panels 
2000 - 4000 Amp Pad Mount 
Installation Manual

 

381333-476 A 
11/2020 

 

DANGER is used in this manual to warn of a 
hazard situation which, if not avoided, will result  
in death or serious injury. 

 

WARNING is used in this manual to warn of a 
hazardous situation which, if not avoided, could 
result in death or serious injury. 

 

CAUTION is used in this manual to warn of a 
hazardous situation which, if not avoided, could 
result in minor or moderate injury. 

Important: 

This manual contains information critical to the proper 
installation and operation of the ASCO SERIES 300 Quick 
Connect Power Panels.  Be certain to read and understand all 
instructions prior to installation and operation.

 

 

The ASCO SERIES 300 Quick Connect Power 
Panel must be installed in  conjunction with a 
transfer switch. 

ASCO SERIES 300 Quick Connect Input Power panels 
are ETL listed to UL1008 standards. ASCO SERIES 300 
Quick Connect Output Panels are ETL listed to UL 891 
Standards for Switchboards. 

Limited Warranty 

When this ASCO SERIES 300 Quick Connect Power Panel is 
installed and operated according to the manual’s instructions 
ASCO Power Technologies will repair or  replace any of its 
mechanical or electrical parts if they are found to be defective in 
material or workmanship within two year of the purchase date.

 

Maintenance 

The ASCO SERIES 300 Quick Connect Power Panels will 
require periodic  maintenance. ASCO Power Technologies 
recommends annual inspections to keep the panel in safe 
operating condition. ASCO Power Technologies recommends 
that the Pre-Operation and Maintenance Checklist under 
Appendix A serve as a basis for annual inspection.

 

Technical Support 

ASCO Power Services are available to assist in resolving 
issues by calling 1-800-800 2726 (ASCO) or emailing 
powerwarranty@ascopower.com. For any other information, 
please refer to ascopower.com 

 

 

 
 

Summary of Contents for 381333-476 A













Reviews: