background image

Exit Device

Delayed Egress

Attention Installer

Any retrofit or other field modification to a fire rated opening 
can potentially impact the fire rating of the opening, and 
Yale Locks & Hardware makes no representations or 
warranties concerning what such impact may be in any 
specific situation.  When retrofitting any portion of an 
existing fire rated opening, or specifying and installing a new 
fire-rated opening, please consult with a code specialist or 
local code official (Authority Having Jurisdiction) to ensure 
compliance with all applicable codes and ratings.

Installation Instructions

For technical support contact Yale

®

 at 800.438.1951 or support@yalelocks.com

80-9470-0162-000 10/18

An ASSA ABLOY Group brand

Available on the following devices:

Rim

Mortise

SquareBolt

®

Concealed Vertical Rod

*Surface Vertical Rod

*Rod Guards Required (made by other manufacturers)

Copyright © 2018, ASSA ABLOY Access and Egress Hardware Group, Inc.  

All rights reserved. Reproduction in whole or in part without the express written 

permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

WARNING

This product can expose you to lead 
which is known to the state of California 
to cause cancer and birth defects or other 
reproductive harm. For more information 
go to www.P65warnings.ca.gov.

Summary of Contents for Yale Delayed Egress

















Reviews: