background image

Exit Keypad Lock Installation Instructions
886F & 896F Series

An ASSA ABLOY Group brand

80-8420-0900 Rev. B (05-08)

FEATURES

Battery Operated (Hardwire Capable)
Motorized Grade 1 Exit Trim
94 User Code Capacity
All Metal Escutcheon and
Pushbuttons
LED Function Indicator
Patented Free-Wheeling Levers

Self-Adjusting for Door Thickness
Weather Resistant
ADA Compliant 12-Button Keypad
Modular Design
(Simple Installation)
Audible Pushbutton
Patented Keypad Blinders

Request to enter input
Emergency, Supervisor, Passage,
Lockout and Master Codes

(Patent # 4,920,773)

(Patent # 7,091,429)

Operational Modes

Secure
Normal locked state. Any
assigned user code can gain
access. Lock/re-lock
automatically.

Lockout
Lockset will not accept any
assigned user codes except
for the Supervisor and
Emergency Codes.

Passage
Maintains unlocked state.
Relocks by entering passage
code the second time

Electronic Battery Operated Security Solution

Finish Care

This lockset is designed to provide the highest standard of product quality and performance. Care should

be taken to insure a long-lasting finish. When cleaning is required use a soft, damp cloth. Using lacquer
thinner, caustic soaps, abrasive cleaners or polishes could damage the coating and result in tarnishing.

NOTE TO INSTALLER

FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN DAMAGE TO THE LOCK AND
VOID THE FACTORY WARRANTY.

NOTE TO INSTALLER

FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN DAMAGE TO THE LOCK AND
VOID THE FACTORY WARRANTY.

®

Summary of Contents for Yale eBoss 886F Series













Reviews: