NOTE:
The remote control will only control the
device which is selected by the
appropriate mode key (AT&T, TV, DVD,
and AUX). The mode key light for the
selected device flashes each time a valid
key is pressed.
Controlling Other Devices
In order to control other devices with your
4:1 Universal Remote Control, you need
to tell the remote control what types of
devices you have. Sections A and B bring
you through the steps needed to do this.
The volume controls will work for the
device mode you are in. If you want to
change this, you should follow the steps
in Section F.
Programming the remote to control
other devices
To use the U-verse remote control for your
other devices, you will need to set up the
TV, DVD and AUX mode keys to control
the devices (Section A).
Please refer to the code list for a list of
supported brands and models. If you do
not find the brand of your device on the
supported code list, please refer to section
B for the search function or you may use
section C for instructions on the learning
feature of your remote control. If you
have an integrated or combination unit
such as a TV/DVD, each component of
the unit may require being set up
separately by setting up both the TV and
DVD mode keys.
NOTE: The DVD and AUX mode keys
can be set up with any code. The TV mode
key can only be set up with TV codes.
AT&T U-verse
Advanced Series
A10 Remote Control
A. Manual Programming
Use the following steps to set up the TV,
DVD or AUX mode keys:
1. Power on the device you want to
program and locate the 4-digit code
from the code list.
2. Press and hold the mode key (TV,
DVD, or AUX) and while holding it
pressed, press the OK key for one
second.
3. Release both keys and all of the
mode keys will flash then the
selected mode key light will stay lit.
4. Enter the 4-digit code by pressing the
numerical keys (0-9). The selected
mode key light will blink for each digit
entry and will remain off after the entry
of the fourth digit - indicating a
successful set up.
5. Point the remote control at the selected
device and press the power key once.
The device should turn off. If the
device stayed on, repeat the steps 1
thru 4 trying each code for your brand
until you find the correct code.
Repeat above steps to set up another
device.
To use the remote control for your U-verse
unit, press the AT&T mode key.
NOTE: If an invalid code is entered or no
key is pressed at all for 30 seconds, the
mode key light flashes for 3 seconds and
turns off. The remote control returns to
normal operation and you will need to
start over from step A2 to set up the
device.
B. Using the Search Function
To search for a particular device code for
DVD or AUX e.g. VCR, use the Manual
Programming for section A and program
DVD or AUX with any VCR code prior
to starting a search.
1. Turn on the device you want to control
and point the remote at that device.
2. Press and hold the mode key (TV,
DVD, or AUX) and while holding it
pressed, press the OK key for one
second.
3. Release both keys and all of the
mode keys will flash then the
selected mode key light will stay lit.
4. Press the power button repetitively
until the selected device responds.
Once your device has responded, press
OK to save the code.
5. To indicate a successful set up, the
selected mode key will turn off and you
are ready to set up another device by
following steps 1 thru 3 of this section.
C. Learning
If the code for your device is not found in
the code list and the search feature does
not work with your device, then the
learning feature may be your best option.
The learning feature lets you "learn"
functions from your original remote
control.
C-I. Learning Commands
1. Press and hold the mode key (TV,
DVD, or AUX) and while holding it
pressed, press the LEARN key for one
second then release both keys.
2. All of the mode keys will flash and
then the selected mode key light will
remain on.
3. On your U-verse remote control, press
and release the key that you want to
teach.
4. While pointing your original remote at
the bottom of your U-verse remote
approximately 1 inch apart, press and
hold the original remote key until the
mode key light blinks once and stays
on. (If there is a learning problem, the
mode key light blinks for three seconds
and stays on. If this happens, repeat
the steps above.)
4. Press and release the DELETE key.
The TV mode key light turns off. All
learned Commands in the remote are
now cleared.
E. Resetting the remote control to the
Factory Default Settings
1. Press and hold the TV key and while
holding it pressed, press the OK key
for one second and release both keys
at the same time.
2. All the mode keys will flash and the
TV mode key light will stay on.
3. Press and hold the DELETE key for 3
seconds until the TV mode LED blinks
and stays off. The remote control is
now reset to factory default settings.
If you want to use the remote control
for your TV and other devices, you will
need to set up the TV, DVD and AUX
mode keys.
4. If no key is pressed within 30 seconds,
the remote control times out. The
selected mode key light flashes for 3
seconds and turns off. The remote
control returns to normal operation
and you will need to start over.
F. Volume Control Set Up Options
The volume controls will work for the
device mode you are in, e.g. if AT&T
mode is selected then volume controls
your AT&T U-verse unit, if TV mode is
selected then volume controls your TV,
etc. If you'd like the volume commands
to operate from just one device, e.g.
always TV, then follow the instructions
in Section F-I. If you'd like the volume
commands to be sent to different devices
depending which mode you are in
(Factory Default), then follow the
instructions in Section F-II.
F-I. Volume Always Controls the same
Device
1. Press and hold the TV key and while
holding it pressed, press the OK key
for 1 full second.
2. Release both keys and all of the mode
keys will flash followed by the TV
mode key light remaining on.
3. Press and hold the MUTE key for 3
seconds until the TV mode key light
briefly turns off then remains on. Press
and release the mode key that you
always want to operate the volume
commands (AT&T, TV, DVD, and
AUX). The selected mode key light
will remain on.
4. Press and release the MUTE key to
save the setting. The selected mode key
light will turn off indicating a
successful initial set up. The volume
commands will be set up for the
selected device despite what mode is
selected. If the selected mode key light
flashes for 3 seconds and turns off,
then the selected mode will have no
volume commands of its own and will
need to start over from step 1 above
and select a different mode to program
the device.
F-II. Volume Control Depends on
Device Selected (Factory Default)
1. Press and hold the TV key and while
holding it pressed, press the OK key
for one second.
2. Release both keys and all of the mode
keys will flash followed by the TV
mode key light remaining on.
3. Press and hold the MUTE key for 3
seconds until the TV mode key light
briefly turns off then stays on.
Caring for the environment by
recycling
This symbol on an AT&T
product means the product
should not be disposed of
with household waste.
Disposal of your charging base, power
supply or remote control.
Please do not dispose of any of the items
in this package with your household
waste. These items should be disposed of
accordance with the national collection
and recycling schemes operated by your
local or regional authority. Alternatively
you may return unwanted items to any
approved AT&T Service Center in your
region.
Find key
FCC Caution
THIS DEVICE COMPLIES WITH PART
15 OF THE FCC RULES.
OPERATION IS SUBJECT TO THE FOL-
LOWING TWO CONDITIONS:
(1) THIS DEVICE MAY NOT CAUSE
HARMFUL INTERFERENCE, AND
(2) THIS DEVICE MUST ACCEPT ANY
INTERFERENCE RECEIVED, INCLUD-
ING INTERFERENCE THAT MAY
CAUSE UNDESIRED OPERATION.
This equipment generates and uses radio
frequency energy, and if not installed and
used properly, that is, in strict accordance
with the manufacturers instructions, it may
cause interference to radio and television
reception. It has been type tested and found
to comply with the limits for remote con-
trol devices in accordance with the speci-
fications in Sub-Parts B and C of Part 15
of FCC Rules, which are designed to pro-
vide reasonable protection against such in-
terference in a residential installation.
However, there is no guarantee that inter-
ference will not occur in a particular in-
stallation. If this equipment does cause in-
terference to radio or television reception,
which can be determined by unplugging
the equipment, try to correct the interfer-
ence by one or more of the following mea-
sures.
• Reorient the antenna of the radio/TV
experiencing the interference.
• Relocate the equipment with respect to
the radio/TV.
• Move the equipment away from the ra-
dio/TV.
• Plug the equipment into an outlet on a
different electrical circuit from the ra-
dio/TV experiencing the interference.
• If necessary, consult your local dealer
for additional suggestions.
The manufacturer is not responsible for
any radio or TV interference caused by un-
authorized modifications to this equipment.
Such modifications could void the user's
authority to operate the equipment.
Code List
TV
Abex
0185
Acme
0010
Admiral
0020 0226 0001
Advent
0116 0176 0922
Adventura
0174
Aiko
0058
Aiwa
0195 0196 0227 0269
Alleron
0051
Amark
0020
Amtron
0053
Akai
0105 0002 0077 1137
1138 0254 1105 1113 1139
Anam National
0053 0003
0025 0042 0193
AOC
0004 0005 0009 1009
0014 0156 0175 0187
Apex
0214 0216 0215 1132
Archer
0020
Aspect
0059
Audiovox
0053 1019 1117
Axion
0177
Bang & Olufsen
0190
Belcor
0004
Bell & Howell
0031 0049 0000 0001
Benq
0081 0083 0101
Bluesky
1155 0144
Bradford
0053
Broksonic
0147 0135 0310
Brokwood
0004
Candle
0004 0009 0174 0008
Capehart
0175
CCE
1153
Celera
0214
Celebrity
0002
Centrios
0169
Centurion
0009
Cetronic
0042
Changhong
0214 0401
Cineral
0058 0144
Citizen
0004 0009 0053 0105 0109
0189 0135 0001 0008 0042 0058
Clairtone
0014
Classic
0214 0401 0042
Coby
1091 1124
Color Voice
0010
Colortyme
0004 0009 0010
Concerto
0004 0009
Concierge
0121
Contec/Cony
0053 0012 0014 0042
Cornea
0050
Craig
0053 0042
Crosley
0062
Crown
0053 0042
Curtis Mathes
0031 0105 0130 0004
0009 0000 0049 0109 0358 0001 0015
CTX
0020
CXC
0053 0042
Cybervision
0144
Daewoo
0130 0004 0009 0100 0005
0138 0043 0140 0039 0444 0080 0042
0058 0017 0010 0126 0018 0127 0019
Daytron
0004 0009
Dell
0209 0028 0132
Diamond Vision
0210 0948 0092
Digimate
1017
Digistar
1019 0165 0118 0116
0167 0132 1020 1151 1152
Dimensia
0031 0000
5. Repeat Steps above for each key you
want the U-verse remote to learn.
Press and release the LEARN key when
all desired remote commands have been
learned.
NOTE:
It is not necessary to have your U-verse
remote control learn every key from your
original remote since most of the keys will
not be used under normal daily use. Best
practice is to teach only the keys that help
you navigate for the best experience, like
your volume up and down, channel up
and down, and DVR functions.
D. Clearing Commands
D-I. To Clear all Learned Commands
(under a single mode)
1. Press and hold the mode key (TV,
DVD, or AUX) and while holding it
pressed, press the LEARN key for one
second then release both keys.
2. All the mode keys will flash and the
selected mode key light will stay on.
3. Press and release the LEARN key
once. The mode key light blinks off.
4. Press and release the DELETE key.
The mode key light turns off. All
learned Commands under that mode
are now cleared.
D-II. To Clear all learned Commands
(under ALL modes)
1. Press and hold the mode key (TV,
DVD, or AUX) and while holding it
pressed, press the LEARN key for one
second then release both keys.
2. All the mode keys will flash and the
selected mode key light will stay on.
3. Press and release the LEARN key twice.
The TV mode key light blinks off.
4. Release the MUTE key to save the
setting. The TV mode key light will
turn off indicating successful set up.
The volume commands will now work
for different devices.
NOTE:
If a programmed mode key has no volume
commands of its own, then the volume
control will normally operate the TV. If
an invalid key is pressed, the selected
mode key light flashes for 3 seconds and
turns off. The remote control returns to
normal operation and you will need to
start over. If no key is pressed within 30
seconds, the remote control times out, the
selected mode key light flashes for 3
seconds and turns off. The remote control
returns to normal operation at which time
you can start over.
G. Battery saving backlight
cancellation feature
In order to extend the life of your battery
between charges, your U-verse remote
control has the ability to toggle between
turning the backlights on or off. If you
wish to use this feature, follow these in-
structions.
1.
Press and hold the TV key and while
holding it pressed, press the OK key
for one second and release both keys
at the same time.
2. All the mode keys flash and the TV
mode key light stays on.
3. Press the GUIDE key and all back-
lights will no longer turn on.
To reverse this process so that the back-
lights turn on when the remote control is
being used, simply follow the same steps
of this section one more time.
H. Charging Base setup
Connect the Charging Base to the back
of your U-verse set top box via the
supplied USB connector or by using the
included plug-in power supply. Place the
remote into the Charging Base to charge
the rechargeable battery in the remote
control. It takes approximately 12 hours
to fully charge the battery in the remote
but you will be able to use your new
remote control within 30 minutes of
charging. To ensure that you have placed
the remote control on the charging base,
the charging indicator located next to the
clock will
show that the battery is being
charged.
H. Find feature
Never lose your remote again! If you have
misplaced the remote control and can not
locate it, simply press the AT&T globe on
the Charging Base and the remote control
will play the AT&T ring tone as well as
flash several of the remote keys. This
should help you locate your lost remote
control.
H-I. Setting the Clock
Use the +H and +M buttons to set the
Hours and Minutes for the clock. Both
the +H and +M buttons are located at the
bottom on your new Charging Base.
H-II. Finding more than one remote
If there is more than one remote and
Charging Base, you can set each Charging
Base to find only its own remote with 16
unique codes. With the first power up of
the Charging Base, it will be set to find
ALL remotes.
To set the Charging Base so that it finds
a specific remote when there are multiple
remote in the household, follow these
instructions:
1. Press and hold both clock setting keys
(+H and +M) at the same time for 3
seconds. The display shows the
current ID, from 1 to 16 or ALL.
2. Press the +M key to cycle from 1 to
16 including a selection for all remotes
in the household.
3. Then press the +H key to confirm the
selection.
To set the remote to the same ID as the
Charging Base, follow these instructions:
1. Press and hold the TV key and while
holding it pressed, press the OK key
for one second and release both keys
at the same time. Next press the
MENU key to enter ID learn mode
(both the AT&T and AUX lights
remain on).
2. Press the Find key on the Charging
Base – the remote will accept the new
ID and the lights will flash once and
then turn off.
3. To exit this mode without changing the
code, simply press any key.
H-III. Dimming and brightening the
clock on the Charging Base:
Simply pressing and holding the Charging
Base find key while the remote is in the
Charging Base causes the display to dim.
Holding down the find key until fully dim
followed by releasing the find key and
holding it down again causes the clock to
be brighter and return to its original
illumination.
I. Troubleshooting Learning
You can only learn one device type under
any one mode key. For example, only
learn TV codes under the TV mode, DVD
codes under the DVD mode, etc. If you
are trying to learn from a "Universal"
remote, it might have more than one code
type stored under a mode.
a. No functions may be stored under the
LEARN key in the AT&T mode.
b. Depending on the remote you are
trying to learn, some keys may not be
learnable.
c. Only one original device type can be
learned per individual mode.
d. Use fresh batteries for your original
remote, and make sure the batteries in
your U-verse remote are fully charged.
e. Keep at least three feet away from
incandescent or low-energy lights
when learning.
f. Before learning, clear all learned
commands (refer to Section D-II) then
try learning 2 or 3 commands initially.
g. Point your original remote at the
bottom end of your U-verse remote so
the IR elements on both remotes are
directly in line with each other (see
diagram to the right). You may need
to adjust the height of either remote to
achieve this.
h. Avoid learning your original remote's
Volume/Mute keys unless you are sure
these operate the same device.
i. Avoid learning your original remote's
VCR or DVD transport keys unless
you’re sure these operate the same
device.
j. If learning the first or second keys for
a mode results in continuous errors
then try the following:
i. End the learn session by pressing the
LEARN key.
ii. Clear out the learned commands for
that mode.
iii. Check the IR elements are correctly
aligned between the two remotes.
iv. Adjust the distance between the two
remotes to be closer (e.g. half an inch)
or a further away (e.g. 2 inches) from
each other.
v. Try learning the original remote for
that mode again. If problems reoccur
with the same key check the original
remote key being learned – does it
transmit? Does it operate the target
device? Try learning that key under a
different
clear
mode. If it learns OK
then it is likely to be a different code
type from the others and cannot be
learned under the same mode.
AT&T
U-verse
remote
Your
original
remote
1 inch
apart
