background image

1/7

AtlasSound.com

TELEPHONE: (800) 876-3333

FAX (800) 765-3435

©2012 Atlas Sound L

.P

.  All rights reserved.  Atlas Sound is a trademark of Atlas Sound L

.P

.  All other trademarks are the property of their respective owners.  All specs are subject to change without notice.  A

TS004369 RevA 5/12  

PM Series

Pendant Mount Loudspeakers

1601 JACK MCKAY BLVD.  

ENNIS, TEXAS 75119  U.S.A.

Safety Instructions

Please Read Carefully Before Installing or Operating

•  Read all instructions carefully
•  Heed all warnings 
•  Assure that the speaker is securely mounted 

Hearing Damage

CAUTION

:  

This professional loudspeaker systems is capable of generating very high sound pressure levels.  
Use care with placement and operation to avoid exposure to excessive levels that can cause permanent hearing damage.

Suspension & Mounting

Suspension or "flying" speaker systems requires training and expertise. Improper rigging of a flying speaker may result in injury, death, equipment 
damage, and legal liability. Installation must be carried out by fully qualified installers, in accordance with all required safety codes and standards at the 
place of installation.

A 5:1 design factor is a generally accepted minimum standard. However, legal requirements for overhead suspension vary by municipality, 
please consult your local safety standards office before installing any product. We also recommend that you thoroughly check any laws and 
bylaws prior to installation.

Loudspeakers flown in theaters, nightclubs, conference centers, or other places of work and entertainment must be provided with an independent, 
correctly rated and securely attached secondary safety — in addition to the principle suspension point(s). This secondary safety must prevent the 
loudspeaker from dropping more than (6") should the principle suspension device fail. If you lack the skills, training, and proper ancillary equipment to 
fly a speaker system, do not attempt to do so.

•  Always assure power is off to amplifiers before making any connections

•  Assure that all electrical equipment is properly grounded

•  Keep instructions for future reference 

•  Should any questions arise after reading this document, please call Atlas Sound Tech Support at 800-876-3333 

Summary of Contents for PM8CX








Reviews: