background image

Rev: 9.27.18

ALWAYS use proper safety precautions:

 

Wear eye protection and use nitrile or latex gloves at all times. 

Have a fire extinguisher available in the area. Run the vehicle outside or in a well ventilated area. The 3C will 

start and stop automatically. To manually stop the 3C mid-cleaning push the Emergency Stop Switch located 

on the front panel. Before performing a cleaning with the 3C check the vehicle’s engine oil and coolant levels 

and top off if needed. If the vehicle’s engine is making any unusual noise check and repair prior to cleaning. 

Check for both pending and hard DTC’s. Always use common sense when using the 3C system.

 

FOR PROFESSIONAL USE ONLY

If you need help or have questions call ATS at (800) 572-6112 for assistance.

This technology has been under development for over 4 years. It is extremely important to follow these directions.

ATS cannot be responsible for any action taken by a shop or technician that is not stated in the following information. 

Doing any procedure that is not specifically stated by ATS is at the users own risk.  

DO NOT USE THE 3C INDUCTION CLEANER ON ANY EXOTIC ENGINES such as, but not limited to; 

Ferrari, Maserati, McLaren, Bugatti, Koenigsegg, Lamborghini, etc. Additionally Do not Clean 

BMW N63-S63 V8 Twin Turbo engines

   

Getting to know your 3C

Air Bleed 

Valve

Chemical 

Reservoir A

Chemical 

Reservoir B

Chemical 

Reservoir C

Compressed 

Air Plug

Emergency

Stop Switch

Manual

Chemical

Shut Off

Start

Clean

Button

Intake

Adapter

Hoses

Cylinder

Selection

Switch

Chemical PSI

Air PSI

Arm/Disarm

Button

Holding

Clamp

Battery

Leads

2 Amp 

fast-blow fuse

Injection Nozzle

3C Cleaning

Hose Assembly

3C Intelligent Induction Cleaner          Quick Start Guide

Patent Pending

TM

Summary of Contents for 3C Intelligent Induction Cleaner









Reviews: