background image

Explosion-proof telephone connecting relay mTCR

 

1

Description

The telephone connecting relay type

mTCR  is  used  as  a  fixed  device  in

areas  that  may  be  at  risk  due  to

explosive gas or dust atmospheres

and which require devices of device

groups  II  and  III  of  the  categories

2G and 2D. 
The  designated  position  of  normal

use is not mandatory.
The telephone connecting relay type

mTCR  is  implemented  in  the  follo-

wing ignition protection classes: 

Ex e ib mb IIC T4 Gb 

Ex tb IIIC T1 35°C Db

IP66
Temperature range 

-40°C  Ta  +70°C
The telephone connecting relay type

mTCR is intended for connection to

analogue  telephone  networks.  It

can be simply installed parallel to a

telephone. 

The  telephone  connecting  relay

serves  for  call  signalling  through

providing  potential-free  switching

contacts  for  the  connection  of

 signalling  devices.  This  means  for

example  that  up  to  two  external

devices  (e.g.  a  horn  and  a  flash

light)  can  be  switched  on  via  call

signal.  The  call  break  bypass  can

be  individually  adjusted  for  one  of

the connected devices. 
The  installation  regulations  in

accordance with IEC/EN 60079-1 4

as  well  as  the  respective  national

installation regulations must always

be taken into consideration.

Device strutcture

 

The telephone connecting relay type

mTCR  has  an  unpainted  housing

made of electrostatically conductive

compressed material.
The  housing  consists  of  a  box-

 shaped  lower  part  for  receiving  the

electronics  module.  The  electronics

module is firmly cast into the lower

part  of  the  housing  and  cannot  be

exchanged. 

The cover is pressed onto the lower

part  of  the  housing  using  four

screws,  with  a  circumferential  seal

positioned  in  between.  This  forms

the non-intrinsically-safe connection

compartment. 

Intrinsically safe DIP switches

An  intrinsically  safe  4-pole  sliding

switch extends out from the casting

within  the  device  (see  device  over-

view)  for  pre-setting  the  desired

mode of operation. 

Designation 

Type

Article no.

 

Order data

 

 

Telephone connecting relay 

mTCR

410 100 100

 

 

mTCR

mTCR 3.1_E

Summary of Contents for mTCR







Reviews: