background image

 
 
 
 
 
 
 

 

 

page -

  

1

  

-

  

Australian Hydronic Supplies 

10 Frankston Gardens Drive 

Carrum Downs, Victoria,  

Australia  3201 

 

 

HYDRONIC RADIANT HEATING SYSTEM

 

 

Hydronic radiant heating & cooling systems can be installed in many ways to create a wonderfully 
warm room environment

 

These include: 

 

1.

 

Pipes embedded in the concrete floor. 

2.

 

Pipes in a floating floor system. 

3.

 

Pipes fixed to the underside of a wooden floor. 

4.

 

Pipes embedded in the walls of a room. 

5.

 

Pipes embedded in the ceiling of a room. 

6.

 

All these methods offer many practical benefits to suit the needs of all.  

7.

 

Hydronic radiant heating has been used for centuries. In the last few years, significant improvements in 
the technology together with the realisation of the benefits of this form of heating and cooling have created 
a rapid rise in installations. 

Tiemme

 has been one of the companies leading the way. 

 

Benefits

 - 

Tiemme 

radiant

 floor, wall or ceiling 

heating, provides energy saving with comfort, quiet 
and clean operation, with room versatility and choice 
of energy usage.  

Energy Saving

 -

 

Room temperatures can be set as 

much as 3 degrees lower and still maintain the 
required comfort level. In houses with high ceilings the 
savings can be significant. 

Ultimate Comfort 

-

 

Rooms can be heated to different 

temperatures according  to  their  usage.  Zones  can  be 
set  to  heat  rooms  at  different  times  to  eliminate  cold 
rooms  often  during  a  relative  short  period  of  usage. 
The  floors  are  always  comfortably  warm  no  matter 
what the floor coverings are. 

Quiet  Operation 

Tiemme 

radiant  floor  heating 

systems operate without noise and draughts. Air movement is kept to a minimum so dust and germs are not spread 
around the house. 

Choice  of  Surfaces 

-

 

Tiemme

  radiant  heating  systems  can  be  installed  in  a  concrete  floor  on  the  ground  or 

suspended below with wooden floors and even in the walls or ceiling. The choices are unlimited. 

Freedom  to  decorate 

-

 

As  the  heat  gently  radiates  from  the  whole  of  the  floor  there  are  no  obstructions  or 

limitations for the placement of furniture. 

Choice of energy 

 

Tiemme

 radiant systems can be powered by a gas-fired boiler, a combination of heat pump 

and  solar  collectors,  solid  fuel  boiler  or  any  new  energy  system  yet  to  be  discovered.  This  means  your  heating 
system is always ready for the future. 

Healthy Choice 

-

 Over the years people who have switched from forced air to floor radiant heating have greatly 

improved their allergy problems. This is attributed to less dust blowing around. 

Zero  maintenance 

-

 

Once  installed 

Tiemme

  radiant  floor  heating  does  not  require  routine  maintenance  or 

cleaning. 

 

Summary of Contents for TIEMME



























Reviews: