background image

v1.1 J2428

 

OEM S

ERIES

Remote Control Car Starter Installation Manual for Models 28624, 28628

DesignTech International, Inc. • 7955 Cameron Brown Court • Springfield, Virginia  22153  USA • www.designtech-intl.com • 703-866-2000 or 800-337-4468

PLEASE READ COMPLETELY BEFORE BEGINNING

Congratulations on your purchase of the AutoCommand

®

 OEM Series Remote Car Starter.  The AutoCommand

®

 OEM Series Remote Car Starter system allows you to start the car

by remote control from the comfort of your home or office in order to cool it down in the summer or heat it up in the winter.

AutoCommand

®

 OEM Series is for 

automatic transmission/fuel injected vehicles only

. It is an extremely sophisticated system with multiple built-in safety and security

features.

AutoCommand

®

 OEM Series Car Starter:

• Will start your car by remote control, and run the heater, defroster, or

air conditioner to warm up or cool down the car.

• Is designed to start the car if it is in park, and only if the hood is

closed.

•  Has Lock, Unlock and Trunk keyless entry features.

• Will attempt to start the car for up to six seconds, but no longer (to

avoid damage to the starter motor).  Should the car not start, or if it
stalls after starting, the remote starter will make two further attempts
to start it.

•  Has alarm functions including starter kill which becomes active when

the doors are locked with the remote control.

• Will not let the car be driven without the key in the ignition.

• Shuts itself off automatically after 10 or 15 minutes (programmable)  if

you forget to come out to your car.

• Will shut off if the brake pedal is pushed, the hood is opened, or the

transmission is shifted out of park - unless the key is in the ignition and
in the “run” position.

• Allows you to remove the key while leaving the car running with the

doors locked for up to 10 or 15 minutes utilizing the Quick Stop™ Op-
tion. (See Separate User Tip Sheet)

• Starts the car automatically whenever the temperature drops below

0

°

F (-18

°

C), or if the battery voltage drops below 11 volts when the

Cold Start™ Option is used. (See Separate User Tip Sheet)

• Has the “Daily Start™” feature which allows the vehicle to be started

at the same time the following day. (See Separate User Tip Sheet)

• Is quality engineered, microprocessor controlled, and made in the USA

to provide many years of reliable use.

• Comes with a lifetime warranty.

*For free vehicle-specific wire information consult our website at
www.designtech-intl.com

Color

Function

Circuit Type

Required

Pink

Power (+12V)

Input

Yes

White

Accessory

Relay Output

Yes

Yellow

Starter

Relay Output

Yes

Blue

Ignition 1

Relay Output

Yes

Green

Ignition 2

Relay Output

Consult Wiring Diagram

Black

Ground

Input

Yes

Color

Function

Circuit Type

Required

1.

Yellow

Lights

Relay Output

No

2.

Blue

Horn

(–) 400 mA

No

3.

Brown

Accessory

(–) 400 mA

No

4.

Brown/White

Alarm Disable

(–) 400 mA

Consult Wiring Guide

5.

White/Black

Ignition 3

(–) 400 mA

Consult Wiring Guide

6.

Orange

Brake

(+) Input

Yes

7.

Purple

Hood

(–) Input

Yes

8.

Green

Tach

(–) Input

No

9.

Red/White

Alarm Input

(–) Input

No

10.

Red/Black

Diesel

(+/–) Input

No

LED Light
White – Option
Red – Code Learn

Coax Antenna Jack

4-Pin Shock Sensor Input

Lock/Unlock/Trunk Harness

Power Harness

Control Harness

ON/OFF Switch Jack

LED Light Jack

Green “In-Gear” Loop

Parts List included with the AutoCommand

®

 OEM Series Unit:

We highly recommend that all connections be soldered for reliability.

Drill with1/4”and 5/16”
drill bits

Electrical Tape

Soldering Iron

Test meter

Pliers

Screwdriver

Wire Cutters/Strippers

Tools required to install the AutoCommand

®

 OEM Series Unit:

6 Power and Ignition wires

Antenna

Remote Starter
Receiver Module

Transmitter

Siren (Model 28628 only)

Control Harness
(10 position)

2 Relays with relay harnesses
(Model 28628 only)

Shock Sensor
(Model 28628 only)

Alchohol

Pad

Ring Terminal

Plug-In LED

2 Protected by
DesignTech Labels

Alcohol Pad

Green 30 A Fuse

On/Off Control Switch

Warning Label

Following parts included in plastic baggy

3 Pin Door Harness

Yellow Butt Connector

2 Cable Ties

Hood Pin Switch Set

2 Antenna Clips

Wiring Diagram

Summary of Contents for 28624











Reviews: