Automated Logic UNI/32 Technical Instructions Download | Manualshive

Page: 1 / 10

background image

Automated Logic Corporation

•

1150 Roberts Blvd.

•

Kennesaw, GA 30144

•

770/429-3000

•

770/429-3001 Fax

•

www.automatedlogic.com

•

Copyright 2001 Automated Logic Corporation. All rights reserved. Automated Logic, the

Automated Logic logo, SuperVision, Eikon, Alert, and InterOp are registered trademarks of Automated Logic
Corporation. BACnet

®

is a registered trademark of ASHRAE. All other brand and product names are trademarked by

their respective companies.

Technical Instructions

UNI/32

Using the UNI/32 2
Specifications 2
Mounting 3
Power Wiring 3
Communicating with the UNI/32 4

Connecting the UNI/32 to the U-cards 4
Connecting the UNI/32 to an ARC156, MS/TP, or Legacy CMnet network segment 5

Addressing 5
Transferring Memory 6

Transferring Memory in WebCTRL 6
Transferring Memory in SuperVision 7

Using Flow Sensors 7

Troubleshooting Tips 7
Communicating with the Workstation Using SuperVision 8
Formatting the Module 8
LEDs 9
Protection 9
Production Date 9

1
2
3
...
»

Summary of Contents for UNI/32











Reviews:

No comments

Related manuals for UNI/32

Brand: Falcon Pages: 3

Brand: E-fly Pages: 16

Brand: Dakota Digital Pages: 6

CMD-2000 Series

Brand: Dakota Digital Pages: 10

Brand: Z-Wave Pages: 6

Brand: Jabra Pages: 4

Brand: Lattice Semiconductor Pages: 2

Brand: Lathem Pages: 4

Brand: tams elektronik Pages: 36

Brand: Sunnen Pages: 24

Brand: GEA Pages: 13

Brand: WAGNER Pages: 128

Brand: Festo Pages: 62

Brand: Anthem Pages: 8

Brand: National Instruments Pages: 11

Brand: KAR-TECH Pages: 55

10 AMP RVC-MPPT

Brand: Go Power Pages: 17

GYRO TECH Nabco Multi-Module

Brand: Nabco Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands