Get to know us at: www.axvue.com
Please read the following instructions and warnings carefully
Keep this instruction manual for future.
For technical support see FAQ page.
For adult use only.
Adapters:
INSTRUCTION MANUAL
Model- E722
Revised at 12/2020
AXVUE E722 Video Baby Monitor
with 2.8'' LCD Screen and Two Cameras
The SCAN, SELECT, ADD, DELETE, VIEW CAMERA options are only available when multiple
cameras connected with the monitor. Order extra cameras by visiting us at
www.axvue.com or search “Axvue Baby monitor” on Amazon.
1. LED*
2. Microphone
3. Power/Video
4. Talk Back/Zoom
5. Volume Up/Up
6. Menu/OK
7. Right
8. Volume Down/Down
9. Left
10. Speaker
11. Battery Compartment
12. DC Jack
13. Kickstand
× 3
× 1
× 2
Power & Low Battery
Sound Lights
*LED
Keep the distance between sensor
and body
at least 0.6 inch for
accurate temperature result.
1. Night-Vision LED
2. Lens
3. Microphone
4. Speaker
5. Power/Code
6. Temperature Sensor
7. DC Jack
8.
Wall Mounting Hole
0.6 in
Monitor:
TO USE PORTABLE/BATTERY MODE
Step 1:
Charge the battery for at least 8 hours before using portable/battery mode.
Step 2:
Make sure the adapter is plugged into camera.
Step 3:
The battery life can be up to 10 hours if it is fully charged.
Battery life will be shortened if recharging it continuously. Unplug the power adapter when you are
not using it for a long time.
Please charge the battery for
6~
8 hours before using the product.
TO USE PLUGGED-IN MODE
Step 1:
Place the monitor display in living room, bedroom or any place you want to watch your baby.
Use adapter to connect camera with electrical outlet.
Step 2:
Turn on monitor by pressing
Power/Video“ ”
button for 6 seconds until axvue logo or video
shows up on the screen.
Step 3:
Press Power/Video“ ”
button to turn off the video if you only need to hear the voice.
Step 4:
Turn off the monitor completely by pressing and holding
Power/Video“ ”
button for
5 seconds.
The monitor and camera are paired before shipment. If it is unpaired for some reason, please refer
to the following steps:
TO PAIR MONITOR AND CAMERA (ADD CAMERA)
Step 1:
Make sure the camera and monitor are in the same place.
Step 2:
Step 3:
Make sure the power adapter is plugged into
camera and turn on the camera by pressing
Power/Code“ ” button for 6 seconds.
Turn on monitor by pressing
and holding Power/Video
“ ” button for 6 seconds.
６
Step 5:
Step 4:
Red LED flashs
vox
TEMP
C F
1
3
2
4
1
3
2
4
4
2
3
1
6
5
Press
Press
SETUP & USE
3 feet
Figure 1
3 feet
Figure 2
Please charge the battery for at least 8 hours before
using the product.
Step 1:
Test reception first, put the camera in a suitable place that
will provide you the best view of your baby in the crib (Note: Do
not hang up the camera firmly until the initial installation test is
completed). Plug the adapter into the wall outlet and turn on the
camera.
Step 2:
Turn on the monitor by pressing and holding the
Power/
Video“ ”
button for 6 seconds until “axvue” shows up, then the
video will show up on the screen immediately.
If the video does
not show up, please refer to “TO PAIR MONITOR AND CAMERA
(ADD CAMERA)” on the next page. If the video shows up, the
initial installation test is completed, then you can set up the
camera according to the instruction below.
Set Up Camera:
Place the camera on a flat surface, such as a
wardrobe or shelf (Figure 1). Or hang it on the wall (Figure 2). No
matter wherever to place the camera, please make sure to keep it
away from the crib for at least 3 feet and all power cords should be
placed behind the camera properly. Then adjust the angle of the
camera lens until the entire crib shows up on the display, or adjust
it to the best angle that you think to watch your baby.
-Store this product out of the reach of babies (at least 3 feets (0.9 m)
away from the crib). A strap wound around the baby’s neck may result in
asphyxiation. Use a safety clip to clamp the power cord and keep it out
of baby’s reach. Do not use other extension cords. Only use the power
adapter provided.
-Do not touch the exposed part if the adapter is connected with power.
-Test regularly before initial use or when change the position of camera.
-Avoid placing the product in humid place or contacting with liquid. (such as bathtub, sink, etc.)
-Do not apply heat to the product.(such as stoves, radiators, etc.)
-Using the product in ventilated place. Avoid placing it on sofas, cushions, beds or other places which
may block ventilation.
-The product only can be operated by adult. Do not allow baby to play with it. Tiny accessories are
contained, please be careful when unpack and install it.
THIS PRODUCT CAN NOT SUBSTITUE PARENT’S SUPERVISION
ON YOUR CHILD.
WARNING
-Only use the recommended rechargeable battery. Please contact us if you need to change it.
For the contact list, please refer to the last page of the instruction.
-Please clean the battery compartment before using it.
-Avoid short circuits the power supply terminal.
-Remove the battery when you are not using it or when running out of power.
-Keep the battery away from children.
-Dispose of the empty battery properly.
BATTERY WARNING
FEATURES & COMPONENTS
Camera:
６
