background image

NETWORK COMPASS USER MANUAL 

CONTENTS 

 

GENERAL INTRODUCTION TO B&G NETWORK.........................................................2

 

INTRODUCTION TO NETWORK COMPASS.................................................................3

 

COMPASS DISPLAY UNIT.............................................................................................4

 

EXAMPLE SYSTEMS USING NETWORK COMPASS...................................................4

 

INITIAL POWER-UP........................................................................................................5

 

SETTING THE DISPLAY BACK LIGHTING ...................................................................6

 

THE OFF COURSE DISPLAY.........................................................................................7

 

SETTING THE COURSE MEMORIES ............................................................................8

 

THE XTE DISPLAY .........................................................................................................9

 

THE RUDDER DISPLAY...............................................................................................10

 

THE HEAD/LIFT DISPLAY ...........................................................................................11

 

USING THE TIMER .......................................................................................................12

 

SETTING THE TIMER ...................................................................................................13

 

ENABLING/DISABLING THE TIMER BEEPS ..............................................................13

 

ENABLING THE OFF COURSE ALARM......................................................................14

 

SETTING THE COMPASS DAMPING ..........................................................................14

 

SETTING THE COMPASS OFFSET .............................................................................15

 

SETTING THE VARIATION ..........................................................................................15

 

SETTING THE DISPLAY FOR TRUE OR MAGNETIC READINGS .............................16

 

ENABLING THE HEAD/LIFT MODE.............................................................................16

 

SELECTING THE DISPLAY MODE ..............................................................................17

 

CALIBRATING THE COMPASS...................................................................................17

 

OPERATION WITH AUTOPILOTS ...............................................................................18

 

TROUBLESHOOTING ..................................................................................................19

 

INSTALLATION ............................................................................................................20

 

SITING THE FLUXGATE ..............................................................................................21

 

INSTALLATION DATA..................................................................................................22

 

SPECIFICATIONS.........................................................................................................23

 

 

 

1

Summary of Contents for Network System
























Reviews: