background image

Quick Start Guide

Class 1 laser CMOS sensor with a discrete (PNP or NPN) output. Patent pending.

This guide is designed to help you set up and install the Q4X Sensor. For complete information on programming, performance,

troubleshooting, dimensions, and accessories, please refer to the Instruction Manual at 

www.bannerengineering.com

. Search for p/n

181483 to view the Instruction Manual. Use of this document assumes familiarity with pertinent industry standards and practices.
For illustration purposes, the threaded barrel model Q4X images are used throughout this document.

WARNING:

Do not use this device for personnel protection

Using this device for personnel protection could result in serious injury or death.

This device does not include the self-checking redundant circuitry necessary to allow its use in

personnel safety applications. A device failure or malfunction can cause either an energized (on) or de-

energized (off) output condition.

Features

Figure 1. Sensor Features—Threaded Barrel Models

1

2

3

1. Output Indicator (Amber)
2. Display
3. Buttons

Figure 2. Sensor Features—Flush Mount Models

1

2

3

Display and Indicators

The display is a 4-digit, 7-segment LED. The main screen is the Run mode screen.
For 2-pt, BGS, FGS, and DYN TEACH modes, the display shows the current distance to the target in millimeters. For dual TEACH
mode, the display shows the percentage matched to the taught reference surface. A display value of 

 indicates the sensor

has not been taught.

Figure 3. Display in Run Mode

1

2

1. Stability Indicator (STB—Green)
2. Active TEACH Indicators

DYN—Dynamic (Amber)

FGS—Foreground Suppression (Amber)

BGS—Background Suppression (Amber)

Output Indicator

On—Outputs conducting (closed)

Off—Outputs not conducting (open)

Stability Indicator (STB)

On—Stable signal within the specified sensing range

Flashing—Marginal signal, the target is outside the limits

of the specified sensing range, or a multiple peak

condition exists

Off—No target detected within the specified sensing

range

Active TEACH Indicators (DYN, FGS, and BGS)

DYN, FGS, and BGS all off—Two-point TEACH mode

selected (default)

DYN on—Dynamic TEACH mode selected

FGS on—Foreground suppression TEACH mode

selected

BGS on—Background suppression TEACH mode

selected

DYN, FGS, and BGS all on—Dual TEACH mode

selected

Q4X Stainless Steel Laser Sensor

 

 

Original Document

181484 Rev. N

11 January 2023

181484

Summary of Contents for Q4X Series













Reviews: