background image

User’s Manual for

Biometric/Key Pad Safe

WARNING

- Safe can be opened by either Fingerprint, PIN code, 

  and/or Emergency Keys.
- If user resets the safe to Factory Default mode: ANY 

  fingerprint and Factory Default PIN code can open 

  the safe. 
- Register both Fingerprint and PIN code to disable 

  Factory Default mode.
- Register at least two different fingerprints and test a few 

  times before closing the safe door.
- Test with a non-registered fingerprint. If the safe opens, 

  the safe is still in Factory Default mode.
- Avoid leaving safe door open and unattended; it will allow 

  unauthorized individuals to add their fingerprints and/or 

  reprogram the safe, gaining full access to the safe and 

  the contents.
- Test the Emergency Keys and store them in a secure 

   place, NOT inside of the safe.
- To maximize the security and performance of the safe, 

  test registered fingerprints every 6 months.

Read all instructions before using this safe.

A. Initialization Button

B. Battery Compartment

C. Bolts

D. Fingerprint Scanner

E. Indicator Lights

A

B

C

I

D

F

G

E

H

F. Enter Button

G. Key Pad

H. Knob

I. Logo Plate and 

   Emergency Key Access

* Actual model may vary

GETTING STARTED

 

1. Remove Emergency Keys from accessory package

   - To expose the Emergency Key Access, remove Logo Plate 

     (I) screws with provided tool

   - Insert Emergency Key into key access, push and turn 

     counter-clockwise

   - Turn the Knob (H) clockwise to open

 

Note: Store Emergency Keys in a secure place, NOT inside of 

         the safe

2. Continue with INSTALL BATTERIES

  

INSTALL BATTERIES

 

1. With safe door open, remove Battery Compartment (B) cover

   - Insert 4 AA batteries and restore battery cover

   - Continue with FINGERPRINT REGISTRATION

 

FINGERPRINT REGISTRATION

 

IMPORTANT: The safe is in either Factory Default mode or 

Pre-registered mode, test safe to determine factory settings 

below

Factory Default mode: Safe can be opened with ANY 

fingerprint(s)

Pre-registered mode: Safe can NOT open with any fingerprint(s)

During registration the door must remain open and Bolts (C) 

must be in the retracted position. Otherwise, the fingerprint will 

not be saved

To retract bolts:   

   - Insert Emergency Key into key access, push and turn 

     counter-clockwise

   - Turn the Knob (H) clockwise to retract bolts

1. Press and release Initialization Button (A)

 

2. Immediately place a finger on the Fingerprint Scanner (D)

   - Hold finger still

   - Two beeps will be heard recognizing the fingerprint; followed 

      by one long beep

   - Remove finger

   - Registration is complete

 

Successful Registration

Registration is successful when two short beeps are heard, 

followed by one long beep

Unsuccessful Registration

Registration failed if two short beeps are heard, followed by 

three short beeps

 

3. To register another fingerprint, repeat steps 1 - 2

4. Continue with TEST A (NON) REGISTERED FINGERPRINT

Fingerprint Memory Full 

If the Indicator Lights (E) flash and beep twice followed by a few 

green flashes, it indicates the memory is full.  Refer to DELETE 

STORED FINGERPRINTS AND PIN CODE / RESET TO 

FACTORY DEFAULT MODE for more options

  

TEST A (NON) REGISTERED FINGERPRINT

 

1. Test multiple Non-Registered fingerprints

   - Close safe door and lock by turning the Knob (H) counter-

     clockwise

   - To begin the testing process, press and release Enter 

     Button (F)

   - Place a non-registered finger on the Fingerprint Scanner (D)

   - Door should NOT open; three short beeps will be heard     

   - If the door opens with a non-registered fingerprint, 

     registration was unsuccessful; the safe remains in Factory 

     Default mode

 

IMPORTANT: If registration was unsuccessful repeat steps 

under FINGERPRINT REGISTRATION, and test non-registered 

fingerprint 

 

2. Test Registered fingerprint

   - Close safe door and lock by turning the Knob (H) counter-

     clockwise

   - To begin the testing process, press and release Enter 

     Button (F)

   - Place a registered finger on the Fingerprint Scanner (D)

   - Door should OPEN, one long beep will be heard, turn the 

     Knob (H) clockwise to open the safe

   - Fingerprint registration was successful

 

3. Continue with PIN CODE REGISTRATION

PIN CODE REGISTRATION

 

IMPORTANT: Safe only retains one PIN code; Factory Default 

PIN code is 1234

 

1. Press and HOLD number “1” key until the green Indicator 

    Light (E) turns on, release button

   - Enter Factory Default PIN code 1234, press Enter Button 

     (F), one long beep will be heard

   - Enter new PIN code (four to eight digits), press Enter Button 

     (F), two short beeps will be heard

   - Re-enter new PIN code, press Enter Button (F), one long 

     beep will be heard

   - Registration is complete

2. If you hear three short beeps with red/green Indicator Lights 

    (E) flashing, it indicates the new PIN code registration was 

    unsuccessful, repeat step 1

3. Continue with TEST A (NON) REGISTERED PIN CODE

See reverse side for more information

10/12

BC256

U

n

loc

k

Lo

c

k

Reviews: