See reverse side for more information
1/21
BC661
WARNING
Manual for Biometric Keypad Safe
Read all instructions before using this safe
- For security purposes, register the fingerprints and
change the factory default Pin Code A and B as soon as
possible. Default code A:1234 and Code B:123456
- Safe can be opened by either Fingerprint, Pin code,
and /or Emergency Keys.
- Test and Store emergency keys in a secure place, NOT
inside of the safe.
- Avoid leaving safe door open and unattended; it will allow
unauthorized individuals to add their fingerprints and/or
reprogram the safe, gaining full access to the safe and
the contents.
- To maximize the security and performance of the safe,
test registered fingerprints every 6 months.
- Test and make sure the safe works properly before
mounting. Once tested, mount the safe before use.
- Keep children away from safe; they should not play with
or around the safe at anytime. Children at play could
accidentally pull on the safe or accidentally pull on the
safe door causing safe to tip over if not properly mounted.
- Failure to follow these warnings could result in serious
injury or death.
OPENING SAFE WITH ACCESS KEY
1. To expose the key access, remove logo plate screws with
provided Allen Wrench
2. Insert emergency key into key access and turn clockwise;
turn handle to unlocked position and open the safe.
Remove key and keep in a secure location.
INSTALL BATTERIES
1. With the door open, remove the battery cover by sliding
the cover.
2. Insert 4 AA batteries by lining them up in a manner as
indicated by the “+” and “-“signs.
3. Put the arrow of the battery cover align to the arrow on the
compartment, slide the batteries cover back into place.
Restore the battery compartment cover.
NOTE:
DO NOT use any other type of non-alkaline battery.
DO NOT mix new and old batteries.
External Battery Source
9V battery can be used as an external power source. (9V
battery not included) Please remove the bottom black sticker
of keypad, then place 9V battery, touching the metal
contacts under the fingerprint or pin code mode. Safe should
power up, if not switch the polarity of the 9V battery.
LOCK/UNLOCK SAFE
Single Entry Mode
Unlock Safe with Pin Code
1. On the keypad enter registered pin code 4-8 digits and
press " # " to confirm, 2 short beeps will be heard and
green light will be seen.
2. Turn the handle to unlock position to open the safe door.
Unlock Safe with Fingerprint
1. On the scanner place registered fingerprint, 2 short beeps
will be heard and green light will be seen.
2. Turn the handle to unlock position to open the safe door.
Lock Safe
Close door and turn handle to lock position to lock the safe.
FINGERPRINT REGISTRATION
Note: Safe is in Factory Default Mode. ANY fingerprint can
open the safe.
1. With safe open, press and release initialization button
located inside the safe, 2 short beeps will be heard and
yellow flashes will be seen.
2. Immediately place desired finger on fingerprint scanner. 2
short beeps will be heard and yellow flashes will be seen
again. Remove the finger from fingerprint scanner.
3. Repeat step 2 two more times, 1 long beep will be heard.
Fingerprint Registration is completed.
4. Fingerprint Registration can be stored up to 20
different fingerprints.
Important: 1 Fingerprint registration required 3 times of placing
the finger on the scanner to complete.
Successful Registration
1 long beep will be heard and yellow light will flash off.
Unsuccessful Registration
3 short beeps will be heard.
Important
1. Testing a fingerprint that is not registered to make sure the
safe cannot be unlocked to complete the registration process.
2. Please follow the steps " LOCK/UNLOCK SAFE " to test
successful registration.
PIN CODES REGISTRATION
Default code A:1234 and Code B:123456
Pin Code can be 4-8 digits
Code A
1. With the safe open, press and release initialization button,
2 short beeps will be heard and yellow flashes will be seen.
2. On the key pad input new desired Pin Code and press “ # ” to
confirm. 2 short beeps will be heard, Pin Code registration
is completed.
Code B
1. With the safe open, Press “00” on keypad.
2. Press and release initialization button, 3 short beeps will be
heard and yellow flashes will be seen
3. On the keypad input new desired Pin Code and press “ # ” to
confirm. 2 short beeps will be heard, Pin Code registration
is completed.
Successful Registration
2 short beeps will be heard.
Important
1. Testing a pin code that is registered to make sure the safe can
be unlocked to complete the registration process.
2. Please follow the steps " LOCK/UNLOCK SAFE " to test
successful registration.
RESET TO FACTORY DEFAULT MODE
Open the safe door and press initialization button for 5 seconds
and release, 1 long beep will be heard.
The safe is back to factory default mode, any fingerprint can open
the safe.
The sound will be on as it is factory default condition.
Factory default Pin Code A: 1234 / Code B: 123456
Note: If you use Dual Entry Mode (Fingerprint and Pin Code)
before resetting. When you Reset Fingerprint Registration, the
safe entry will back to Single Entry Mode. Please refer to
“SWITCH BETWEEN SINGLE/DUAL ENTRY MODE " to change
the entry mode.
B
A
A. Battery Compartment
B. Initialization Button
C. Fingerprint Scanner
D. Keypad
E. External 9V Battery Source
F. Emergency Key Access
G. Handle
G
Lock
Unlock
C
D
E
F
PARTS OF THE SAFE
