InstructIons for use
en
DIAGrAM of tHe APPLIAnce (fig. 1)
A.
Handle.
B.
Safety lock (if provided).
c.
Gasket.
D.
Separator (if provided).
e.
Defrost water drain plug.
f.
Control panel.
G.
Side motor cooling grille.
DIAGrAM of tHe controL PAneL (fig. 2)
1. Digital temperature display:
indicates the
temperature inside the freezer (fixed display) or
the set temperature (blinking display).
2. Decrease temperature button:
this button
lowers the temperature.
3. Increase temperature button:
this button raises
the temperature.
4. “extra load” button:
activates/deactivates the
large load function.
5. “extra load” LeD (yellow):
indicates, when lit,
that the large load function has been selected.
6. “Green Intelligence” LeD (blue):
indicates,
when lit, that the “Green Intelligence” function
is active (see paragraph “Green Intelligence
function”).
7. Alarm reset button:
stops the acoustic alarm
and the power failure alarm LED (see paragraph
“Alarms”).
8. Alarm LeD (red):
blinks when an alarm condition
occurs (see paragraph “Alarms”).
Before usInG tHe APPLIAnce
Your new appliance is designed to be used in the
household and similar applications such as:
- kitchen areas in shops, offices and other working
environments
- farm houses
- by clients in hotels, motels, residences, bed &
breakfasts.
The product must only be used to store frozen food,
to freeze fresh food and to make ice.
regulations require the appliance to be earthed.
the manufacturer declines all liability for
injury to persons or animals and for damage to
property resulting from failure to observe the
above procedures and reminders.
1.
After unpacking, make sure that the appliance is
undamaged and that the door closes perfectly,
with the gasket remaining intact. Any damage must
be reported to your retailer within 24 hours after
delivery of the appliance.
2.
Wait at least two hours before switching the
appliance on in order to ensure the refrigerant
circuit is fully efficient.
3.
Installation and electrical connection must be
carried out by a qualified technician, according to
the manufacturer’s instructions and local safety
regulations.
4.
Clean the inside of the appliance before using it.
• Before connecting the appliance to the mains
supply, ensure that the voltage corresponds to
that given on the rating plate located on the rear
of the appliance.
• Electrical connections must be made in
accordance with local regulations.
InstALLAtIon
• Unpack the appliance.
• Remove the 4 spacers inserted between the
door and the appliance. (fig 3)
•
Make sure the defrost water drain plug (if provided)
is correctly positioned (E).
• For optimum appliance operation and to avoid
damage when the door is opened, leave a space
of at least 7 cm from the rear wall and 7 cm at the
sides.
(fig 4)
• Fit the accessories (if provided).
sWItcHInG on tHe APPLIAnce
•
Plug in the appliance.
• When the appliance is warm (internal temperature
above 0°C), two dashes appear on the digital
display
(1)
.
• The red alarm LED
(8)
blinks and the acoustic
alarm sounds.
• The “Green Intelligence” LED
(6)
is on.
• Press the reset button
(7)
to deactivate the
acoustic alarm.
• The acoustic alarm stops while the red alarm LED
continues to blink.
• When the appliance reaches a temperature of at
least -12°C the red LED
(8)
stops blinking.
• Food can now be placed inside the freezer.
• The “Green Intelligence” LED
(6)
will remain lit until
the temperature set on the display is reached.
note:
Thanks to the efficient lid seal, the appliance
lid will not re-open easily immediately after closing. It
is necessary to wait a few minutes.
teMPerAture ADJustMent
The appliance is normally factory-set for operation at
the recommended temperature of -18°C. The internal
temperature setting can be adjusted between -17°C
and -24°C or set to ECONOMY mode (see paragraph
“ECO function”). Proceed as follows:
• Press one of the two temperature adjustment
buttons
(2; 3)
once.
• The digital display
(I)
will blink, showing the
previous temperature setting.
• Press the button
(3)
several times as required for
a warmer temperature setting. The value changes
by 1°C with each press of the button. During this
process, the value shown on the digital display
blinks.
• Press button
(2)
several times as required to lower
the temperature. The value changes by 1°C with
