background image

                    

 75.1041.08 LO21U 20150708 

 

Page 1 of 5 

PRODUCT 
DESCRIPTION

 

TECHNICAL 
SPECIFICATIONS

 

USERS GUIDE

  

LO-21U 

LOCKOUT RELAY 

SAFETY 
PRECAUTIONS

 

 

 

 
 

The LO-21U (PN: 10LO21U) is a micro-processed lock out module designed to operate on swing door applications with 
BEA’s Bodyguard or DK-12 overhead presence sensor.  The LO-21U interprets door open or door closed position based 
upon motor voltage input. The motor voltage information is sent from the LO-21U to the Bodyguard or DK-12 via data lines. 
The LO-21U provides optional safety beam input (dry contacts) to override the inhibit signal during closing.   
 

 
  

 
 
 

 

DESCRIPTION 

SPECIFICATION 

Supply voltage 

12 to 24 VAC / 15 to 24 VDC 

Operating frequency 

4 MHz (Microprocessor) 

Power consumption 

10 mA at rest, 50 mA Maximum 

Output 

(2) SPST Relays 

Maximum voltage – Relay contacts 

60 VDC, 120 VAC 

Maximum current – Relay contacts 

2A DC, 0.5 A AC 

 
 
 

 
 

 

 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 

 
 
 
 
 
 

 

Shut off all power going to the header before attempting any wiring procedures. 

 

Maintain a clean & safe environment when working in public areas. 

 

Constantly be aware of pedestrian traffic around the door area. 

 

Always  stop  pedestrian  traffic  through  the  doorway  when  performing  tests  that  may  result  in  unexpected 

reactions by the door. 

 

Always check placement of all wiring before powering up to insure that moving door parts will not catch any 

wires and cause damage to equipment. 

 

Ensure compliance with all applicable safety standards (i.e. ANSI A156.10) upon completion of installation. 

 
 
 
 
 
 
 
 
 
 
 
 

COMPONENT ID

 

 

Green LED     Dipswitches 
 
   Red LED 

OBSOLETE

Summary of Contents for LO-21U






Reviews: