Fig.2
Fig.1
Fig.3
Note: Drawings for illustrations purpose only. May not
reflect the actual product. Not to scale.
Set Up of Vacuum Product
Brush Assembly
Align the curvature of brush with the suction head and
insert the brush into it securely (Fig.1).
Suction Head Assembly
Carefully discard the cardboard wrap around the impeller.
Don’t try to pull the wrap away directly, but cut and unroll it.
Any damage on impeller may cause it to function improperly.
Screw the suction head securely to the threaded connector as
shown (Fig.2).
Battery Assembly
Unscrew the battery cover and take out the battery holder.
Place 8 AA batteries into the battery holder according to the
polarity marked on it.
Align the rib and slide the battery
holder into the compartment with the
word “TOP” facing outwards as shown
(Fig.3).
Screw the battery cover on tight and
make sure it is secure (avoid stripping
the screw).
CAUTION: Do not press the button to
turn the product on until the cleaner is
submerged in the water and water level
is above the water vent.
Cleaning Your Pool or Spa
Place the product into water and make sure water level is above
the water vent. You can adjust the product length by unscrewing
the pole lock to release the top pole and then extend it to the
desired length according to your pool or spa size. Secure by
tightening the pole lock. Press the “I” marking on the button to start
vacuuming.
CAUTION:
Never submerge the handle in water. During operation,
avoid water contact with the handle and button. Never use the
product without filter basket in place. This can cause permanent
damage to the product impeller and motor.
Cleaning the Pre-filter Bag
WARNING!
Turn off the product before proceeding following steps.
NOTE:
Water will be stored inside the transparent tube and the
pole after use. To remove the water, lift the product from the pool or
spa with the nozzle facing down to allow the water to drain out.
1. Pull the edge (on back side) of cover to lift its tab (inside) from
the notch on the body, and then pull it down to completely
release the cover (Fig.4).
2. Pull out the pre-filter bag. Empty this bag by removing the leaves
and other debris, and then rinse it. Rinse the cover and make
sure its suction hole is not clogged (Fig.5).
3. Reverse the previous steps to assemble the pre-filter bag back
to the cover and then the cover to the body. Make sure the tabs
on cover inside (2 sides) are secured in the notch of the body
before next operation (Fig.6).
Owner’s Manual
Model No. #58340
AquaScan Electric Pool Vacuum
AquaScan Electric Pool Vacuum
is ideal for cleaning small soft wall
pools, kiddie pools and inflatable spas. Its battery-powered pump provides
a cordless and hose-free solution for pool cleaning. Its lightweight design
ensures quick elimination of sand, gravel and other debris from the bottom
of a pool or spa with minimum effort.
Specifications
Motor: 12V DC
Batteries: Requires 8 x 1.5V AA (Not included)
WARNING!
• This is not a toy. Keep children out of reach of this product and its
accessories.
• This product creates suction. Keep hair, loose clothing, fingers, and all
parts of body away from nozzle.
• Never use this product when person is in water.
Battery Precaution
• Do not mix old and new batteries.
• Do not mix the different types of batteries. Do not mix alkaline, standard
(Carbon - Zinc), or rechargeable (Nickel - Cadmium) batteries.
• Ensure batteries are installed correctly with regard to polarity (+ and -).
• Do not short-circuit the battery.
• Never attempt to recharge primary batteries as this may cause leakage,
fire, or explosion.
• Rechargeable batteries are to be removed from this product before being
charged.
• Never attempt to disassemble or open batteries as this can lead to
electrolyte burns.
• Remove batteries from equipment which is not to be used for an
extended period of time.
• Exhausted batteries are to be removed from this product.
• Do not dispose of product and its batteries in fire. Check your local
regulations for proper disposal instructions.
• Batteries shall not be exposed to excessive heat such as sunshine, fire
or the similar.
• Keep batteries out of the reach of children.
• Only use 8 x 1.5V AA batteries (not included).
CAUTION
- This product is designed for underwater use only. Do not attempt to use
this product to clean anything other than your pool or spa. It must be
submerged in water over the water vent.
- Do not operate this product out of water. It may damage the motor.
- Do not scrape the suction head against acrylic spa, as this may damage
the surface of the spa.
- Do not insert any object into the water vent.
- Do not leave the product in pool or spa when not in use.
- Never submerge the handle in water.
- Never block the water vent when in use.
Parts Reference Overview
Before using your AquaScan Electric Pool Vacuum, take a few minutes to
be familiar to it.
1
S-S-005142
NO.
Description
Battery cover
Battery holder
Handle
On “I”/Off “O” button
Adjustable pole
Pole lock
Impeller
Water vent
Suction head
Brush
1
2
3
4
5
6
7
8
9
10
